Have you enabled the indication of the temperature at the front screen?
The photo is from HK1 Box (S905X3) but you can do the same at your TVbox.
Have you enabled the indication of the temperature at the front screen?
Yes.
Checked my network connections and all is well now relating to Gb Managed switch to managed switch connection was not at Gb speeds. Reset switch and that part is good now.
pete# iperf3 -c 192.168.244.191
Connecting to host 192.168.244.191, port 5201
[ 5] local 192.168.244.232 port 44374 connected to 192.168.244.191 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 112 MBytes 939 Mbits/sec 0 656 KBytes
[ 5] 1.00-2.00 sec 111 MBytes 933 Mbits/sec 0 694 KBytes
[ 5] 2.00-3.00 sec 108 MBytes 902 Mbits/sec 60 646 KBytes
[ 5] 3.00-4.00 sec 104 MBytes 870 Mbits/sec 52 188 KBytes
[ 5] 4.00-5.00 sec 102 MBytes 860 Mbits/sec 0 378 KBytes
[ 5] 5.00-6.00 sec 105 MBytes 881 Mbits/sec 0 413 KBytes
[ 5] 6.00-7.00 sec 111 MBytes 933 Mbits/sec 0 419 KBytes
[ 5] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 0 427 KBytes
[ 5] 8.00-9.00 sec 111 MBytes 933 Mbits/sec 0 433 KBytes
[ 5] 9.00-10.00 sec 104 MBytes 870 Mbits/sec 25 304 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.05 GBytes 906 Mbits/sec 137 sender
[ 5] 0.00-10.00 sec 1.05 GBytes 903 Mbits/sec receiver
iperf Done.
Watched a few movies last night and all was well. This morning the device was off and I had to restart it. I have no power settings configured. Did configure the included IR remote and it is working fine now.
Not too concerned about heat. Just the auto shutdown or sleep when I switch to another video source.
Power button is working fine on new style IR remote that came with device.
Nice!!!
Glad you are up n running
Was wondering about your first Test Results?
See you have edited Post.
Was thinking ethernet Ports on Ruckus were 100Mb
Recently discovered on My Linksys High speed Router
Ports are 100Mb only
Happy Testing
Thank you @freddy . I am using the Ethernet port on the device. The wireless Ruckus APs do have two Gb ports on them. I prefer to use Ethernet as it is all over the house.
Reason for the slow test results earlier was that the main managed switch to the TV managed switch was talking 100Mbs. I reset it and it was fine. Noticed that my Denon AVR only talks 100Mbs.
I switched the configuration of the remote to the included stock remote which is OK. I was though still using the larger MCE IR remote.
It does go to sleep / shuts down when I have the TV set off. The old box would not do this but would turn on the TV via CEC when I would press a button on the remote.
Tested HDHomerun tuner streaming just fine.
I put copper heatsink, max. temp is 62C on idle 42C. I will make some additional holes, should get another 5-10C.
But still cpu load is too high on NE version.
Thank you. Might do that. Now when not utilizing the box it goes to sleep / shuts off. I am able to turn it on and via CEC it turns on the TV which works for me.
Last time I checked after a few hours saw this:
CoreELEC:~ # sensors
soc_thermal-virtual-0
Adapter: Virtual device
temp1: +69.4°C (crit = +105.0°C)
ddr_thermal-virtual-0
Adapter: Virtual device
temp1: +71.9°C (crit = +105.0°C)
around 10 °C of passive cooling would suit me fine. Did you just put a heat sink on the CPU? Do you have any pictures? I have a second one not utilized yet and can take this second one apart before putting it in to production.
Hello:
Sorry if this is not the right place…
Vontar X4, X905X4, CoreELEC 20.0 ne.
Trying to map some buttons of the remote (4 buttons: “APPS”, “FORWARD”, “REWIND”, “MUTE” for functions: CODEC INFO / FASTFORWARD / FASTREWIND / PLAY-PAUSE).
Obtaining the keys:
systemctl stop kodi
systemctl stop eventlircd
CoreELEC:~ # ir-keytable -p NEC,RC-5,RC-6,JVC,SONY -t
Protocols changed to rc-5 jvc sony nec rc-6
Testing events. Please, press CTRL-C to abort.
200.268020: lirc protocol(nec): scancode = 0x10f
200.268041: event type EV_MSC(0x04): scancode = 0x10f
299.456018: lirc protocol(nec): scancode = 0x14b
299.456040: event type EV_MSC(0x04): scancode = 0x14b
320.304265: lirc protocol(nec): scancode = 0x14f
320.304291: event type EV_MSC(0x04): scancode = 0x14f
365.384289: lirc protocol(nec): scancode = 0x141
365.384330: event type EV_MSC(0x04): scancode = 0x141
No one of the 4 mapped keys is working:
0x41 164 #KEY_PLAYPAUSE
0x4b 147 #FASTREWIND
0x4f 146 #FASTFORWARD
0x0f 24 #O-CODEC INFO
What I’m not doing well?
Kind regards
remote.conf :
#*********************************************************************************************************
#this file is configuration for each factory remote device
# work_mode 0 :software mode 1 :hardware mode
# repeat_enable 0 :disable repeat 1 :enable repeat
#
# factory_code each device has it's unique factory code.
# pattern:custom_code(16bit)+index_code(16bit)
# examble: 0xff000001 = 0xff00(custom cod) 0001 (index)
#
# release_delay unit:ms.release will report from kernel to user layer after this period of time
# from press or repeat triggered.
#
# debug_enable 0 :debug disable 1 :debug disable
#
# SW MODE:
# bit_count how many bits in each frame
# tw_leader_act time window for leader active
# tw_bit0 time window for bit0 time.
# tw_bit1 time window for bit1 time
# tw_repeat_leader time window for repeat leader
# REG
# reg_base_gen set value for PREG_IR_DEC_BASE_GEN
# reg_control set value for PREG_IR_DEC_CONTROL
# reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE
# reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE
# reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
# reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME
#*************************************************************************************************************
#amlogic NEC remote
factory_code = 0xfe010000
work_mode = 0
repeat_enable = 1
repeat_delay = 120
repeat_peroid = 33
release_delay = 121
debug_enable = 1
#fn_key_scancode = 0x00
left_key_scancode = 0x51
right_key_scancode = 0x50
up_key_scancode = 0x16
down_key_scancode = 0x1a
ok_key_scancode = 0x13
mouse_begin
0 0x51 //mouse key left
1 0x50 //mouse key right
2 0x16 //mouse key up
3 0x1a //mouse key down
mouse_end
key_begin
# KEY Code Key_Action Kodi_Action
0x40 116 #KEY_POWER power ON/OFF
0x18 115 #KEY_VOLUMEUP volume_up VOL+
0x10 114 #KEY_VOLUMEDOWN volume_down VOL-
0x43 23 #KEY_I i Info
0x00 156 #KEY_BOOKMARKS favorites Favorites
0x19 158 #KEY_BACK back(escape) EXIT(work as 1)
0x16 103 #KEY_UP up UP
0x51 105 #KEY_LEFT left LEFT
0x13 28 #KEY_ENTER return DPAD_CENTER
0x50 106 #KEY_RIGHT right RIGHT
0x1a 108 #KEY_DOWN down DOWN
0x11 172 #KEY_HOME home(browser_home) HOME(work as 172)
0x4c 46 #KEY_C c MENU
0x59 165 #KEY_PREVIOUSSONG prev_track PREV
0x5a 164 #KEY_PLAYPAUSE play_pause PLAY_PAUSE
0x58 163 #KEY_NEXTSONG next_track NEXT
0x47 24 #KEY_O o O-CODEC INFO
0x01 11 #KEY_0 zero
0x42 14 #KEY_BACKSPACE backspace
0x4e 2 #KEY_1 one
0x0d 3 #KEY_2 two
0x0c 4 #KEY_3 three
0x4a 5 #KEY_4 four
0x09 6 #KEY_5 five
0x08 7 #KEY_6 six
0x46 8 #KEY_7 seven
0x05 9 #KEY_8 eight
0x04 10 #KEY_9 nine
0x41 164 #KEY_PLAYPAUSE
0x4b 147 #FASTREWIND
0x4f 146 #FASTFORWARD
0x0f 24 #O-CODEC INFO
# 0x41 113 #MUTE
# 0x52 124 #MEDIA_PAUSE
# 0x0a 257 #MUSIC
# 0x49 261 #PICTURE PLAYER
# 0x4d 263 #SHORTCUT_VIDEOPLAYER
# 0x48 262 #SHORTCUT_FILEBROWSER
# 0x03 217 #SEARCH
# 0x0e 34 #EPG
# 0x54 120 #FAST_FORWARD
# 0x55 121 #REWIND
# 0x52 128 #MEDIA_STOP
# 0x45 264 #ONEKEY_ZOOM
# 0x06 265 #SHORTCUT_SUBTITLE
# 0x44 266 #KODI
# 0x0f 233 #MAIN_MENU
# 0x12 269 #F9
# 0x0a 111 #MUSIC
# 0x4d 101 #(F3)VIDEO
# 0x49 66 #(F1)PHOTO
# 0x48 77 #(F2)FILE
# 0x12 88 #(F9)CLEAN
# 0xf2 140 #F10 oritation
# 0x4b 140 #F10 oritation
# 0x45 99 #(F6)ZOOM
key_end
The codes you scanned are 0x10f
, 0x14b
, 0x14f
, 0x141
, but you wrote them as 0x0f
, 0x4b
, etc in the config, with missing 1
, they’re not the same codes.
Well… the codes were right.
The problem was that in .config folder I had other file for other remote (remote2.conf), and, for any reason, CoreELEC used “remote2.conf” also for this remote (priority: remote2.conf > remote.conf).
After deleting remote2.conf, it works with the 4 new mapped keys.
Ok. Remote problem solved… but I have other new one
Vontar X4, S905X4, CoreELEC 20.0 ne.
When I shutdown the Vontar X4, with remote, with Power menu, or using ssh:
shutdown now
the TV-box seems really remain in standby or something like that (blue and red lights in LED display).
The “problem” is that I have a cooling fan connected using USB to Vontar X4, with the intention of shutdown the cooling fan when Vontar X4 is shutdown… but cooling fan continues working after “shutdown” of the TV-box.
OK; I know that I can remove USB or retire the plug of the TV-Box from electricity, but my intention is to use the TV-Box remotely, and, after ssh:
shutdown now
That all the system be off, including the cooling fan.
Is there any option to “power off” the cooling fan after “shutdown” the Vontar X4?
Kind regards
One question about this device: is Android 64bit or 32bit?
If 32bit does a 64bit Android image exist?
As far as i know, it is 64Bit (has 64 Bit Kernel), but has no 64 Bit ABI installed.
There is no softawre/firmware way to “power off” the cooling fan after shutdown.
There are several hardware mods to do that.
Here you go:
Bad news for me
See this example for a microcontroller board:
You can do same thing, as TV-Box usually has a standby-light connector, where a signal-inverter (second link) could be attached to LED(+), which in turn switches off fan with other transister (first link).
Thanks for the link, but it seems too difficult for me.
Kind regards
Use passive cooling instead. It appears from the posts here that it does work OK.
An alternative as mentioned would be a hardware modification. Here utilize Home Assistant with Tasmota firmware WiFi devices. You could manage your Kodi box with HA. You could configure an ESP01 relay with Tasmota and use Mosquitto…which personally is a tad much.
Here is what you would see in HA with a temperature sensor connected to a Tasmota Device and MQTT.
These boxes…
Hmmmmmm…
USB ports are always hot/ powered.
Could try a different source for USB Fan
Like TV port if accessible
I like AC Infinity
Speed control/ expandable/off setting
Was Binge Watching TV “Series The Last Of Us”
1080 playback hour or so…
Happy Testing
Cool … :).
About | FAQ | Terms of Service | Privacy Policy | Legal Notice