[ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9.113 (relkai@hammbwcor01) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #1 SMP PREEMPT Tue Oct 20 01:01:53 UTC 2020 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] CoreELEC dt-id: gxl_p231_1g_m8s_dvb [ 0.000000@0] Machine model: Amlogic [ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000007400000, len:36 MiB [ 0.000000@0] 05000000 - 07400000, 36864 KB, linux,secmon [ 0.000000@0] __reserved_mem_alloc_size, start:0x000000007f800000, end:0x0000000080000000, len:8 MiB [ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:8 MB [ 0.000000@0] 3e000000 - 40000000, 32768 KB, linux,di_cma [ 0.000000@0] 3d000000 - 3e000000, 16384 KB, linux,vdin1_cma [ 0.000000@0] Reserved memory: created DMA memory pool at 0x000000003d000000, size 0 MiB [ 0.000000@0] 3d000000 - 3d000000, 0 KB, linux,ppmgr [ 0.000000@0] 20400000 - 33800000, 315392 KB, linux,codec_mm_cma [ 0.000000@0] 3d000000 - 3d000000, 0 KB, linux,codec_mm_reserved [ 0.000000@0] cma: Reserved 8 MiB at 0x000000003c800000 [ 0.000000@0] On node 0 totalpages: 261888 [ 0.000000@0] DMA zone: 4092 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 261888 pages, LIFO batch:31 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv0.2 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: Trusted OS migration not required [ 0.000000@0] percpu: Embedded 22 pages/cpu @ffffffc03c754000 s51672 r8192 d30248 u90112 [ 0.000000@0] pcpu-alloc: s51672 r8192 d30248 u90112 alloc=22*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257796 [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=4 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 pq= androidboot.firstboot=0 jtag=apao androidboot.hardware=amlogic mac=D0:76:58:11:CF:07 androidboot.mac=D0:76:58:11:CF:07 androidboot.slot_suffix=_a bootfromusb systemd.show_status=auto [ 0.000000@0] fb: osd1 [ 0.000000@0] fb: loaded [ 0.000000@0] fb: 0x3d800000 [ 0.000000@0] fb: 1080p60hz [ 0.000000@0] vout: 1080p60hz [ 0.000000@0] vout: enable: 1 [ 0.000000@0] vout: get hdmimode: 1080p60hz [ 0.000000@0] vout: get cvbsmode: 576cvbs [ 0.000000@0] [amvecm] pq string error !!! [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000@0] Memory: 583224K/1047552K available (12222K kernel code, 1894K rwdata, 9564K rodata, 4800K init, 1484K bss, 54728K reserved, 409600K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009c70000 ( 12224 KB) [ 0.000000@0] .rodata : 0xffffff8009c70000 - 0xffffff800a5d0000 ( 9600 KB) [ 0.000000@0] .init : 0xffffff800a5d0000 - 0xffffff800aa80000 ( 4800 KB) [ 0.000000@0] .data : 0xffffff800aa80000 - 0xffffff800ac59808 ( 1895 KB) [ 0.000000@0] .bss : 0xffffff800ac59808 - 0xffffff800adcca64 ( 1485 KB) [ 0.000000@0] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00004000 - 0xffffffbf01000000 ( 15 MB actual) [ 0.000000@0] memory : 0xffffffc000100000 - 0xffffffc040000000 ( 1023 MB) [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized [ 0.000000@0] amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] amlogic_init_gpu: register meson gpu clk [ 0.000000@0] amlogic_init_media: register meson media clk [ 0.000000@0] amlogic_init_misc: register meson misc clk [ 0.000000@0] gxl_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000044@0] meson_bc_timer: mclk->mux_reg =ffffff8008008990,mclk->reg =ffffff800800a994 [ 0.000544@0] Console: colour dummy device 80x25 [ 0.000563@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000573@0] pid_max: default: 32768 minimum: 301 [ 0.000673@0] Security Framework initialized [ 0.000683@0] SELinux: Initializing. [ 0.000730@0] SELinux: Starting in permissive mode [ 0.000762@0] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000769@0] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.001432@0] ftrace: allocating 41818 entries in 164 pages [ 0.072100@0] sched-energy: CPU device node has no sched-energy-costs [ 0.072118@0] CPU0: update cpu_capacity 1024 [ 0.072134@0] ASID allocator initialised with 65536 entries [ 0.114692@0] secmon: can't fine clear_range [ 0.115512@0] Meson chip version = RevD (21:D - 4:0) [ 0.160204@1] Detected VIPT I-cache on CPU1 [ 0.160265@1] CPU1: update cpu_capacity 1024 [ 0.160267@1] CPU1: Booted secondary processor [410fd034] [ 0.192251@2] Detected VIPT I-cache on CPU2 [ 0.192301@2] CPU2: update cpu_capacity 1024 [ 0.192303@2] CPU2: Booted secondary processor [410fd034] [ 0.224323@3] Detected VIPT I-cache on CPU3 [ 0.224373@3] CPU3: update cpu_capacity 1024 [ 0.224375@3] CPU3: Booted secondary processor [410fd034] [ 0.224462@0] Brought up 4 CPUs [ 0.224490@0] SMP: Total of 4 processors activated. [ 0.224498@0] CPU features: detected feature: 32-bit EL0 Support [ 0.224580@0] CPU: All CPU(s) started at EL2 [ 0.224609@0] alternatives: patching kernel code [ 0.225537@0] devtmpfs: initialized [ 0.242019@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.242044@0] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.242230@0] pinctrl core: initialized pinctrl subsystem [ 0.243112@0] NET: Registered protocol family 16 [ 0.244732@0] schedtune: init normalization constants... [ 0.244741@0] schedtune: no energy model data [ 0.244745@0] schedtune: disabled! [ 0.260425@0] cpuidle: using governor menu [ 0.260544@0] register canvas platform driver [ 0.260570@0] register rdma platform driver [ 0.262112@0] vdso: 2 pages (1 code @ ffffff8009c77000, 1 data @ ffffff800aa85000) [ 0.262131@0] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.263656@1] DMA: preallocated 2048 KiB pool for atomic allocations [ 0.263855@1] clkmsr: clkmsr: driver init [ 0.263865@1] codec_mm_module_init [ 0.263895@1] media_configs_system_init [ 0.266211@1] aml_iomap: amlogic iomap probe done [ 0.269579@1] vpu: driver version: v20190329(2-gxl) [ 0.269595@1] vpu: load vpu_clk: 666666667Hz(7) [ 0.269781@1] vpu: clktree_init [ 0.269849@1] vpu: vpu_probe OK [ 0.272855@1] clkmsr: msr_clk_reg0=ffffff800822975c,msr_clk_reg2=ffffff800822b764 [ 0.272875@1] clkmsr c110875c.meson_clk_msr: failed to get msr ring reg0 [ 0.274876@1] aml_vdac_config_probe: cpu_id:0, name:meson-gx_l_m-vdac [ 0.275094@1] aml_vdac_probe: ok [ 0.278035@1] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.278129@1] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma [ 0.278136@1] codec_mm_probe ok [ 0.278366@1] canvas_probe reg=00000000c8838000,size=400 [ 0.278390@1] canvas maped reg_base =ffffff8008245000 [ 0.284451@1] cvbs_out: cvbsout_probe, cpu_id:0,name:meson-gxl-cvbsout [ 0.284626@1] cvbs_out: find performance_pal config [ 0.284644@1] vout: vout1: register server: cvbs_vout_server [ 0.284649@1] cvbs_out: register cvbs module server ok [ 0.284654@1] vout: vout2: register server: cvbs_vout2_server [ 0.284659@1] cvbs_out: register cvbs module vout2 server ok [ 0.284666@1] cvbs_out: chrdev devno 264241152 for disp [ 0.284930@1] cvbs_out: create cdev cvbs [ 0.284937@1] cvbs_out: cvbsout_probe OK [ 0.287138@1] rdma_probe,cpu_type:1, ver:0, len:8 [ 0.287153@1] vpu: switch_vpu_mem_pd: unsupport vpu mod: 57 [ 0.287472@1] rdma_register, rdma_table_addr ffffff8008247000 rdma_table_addr_phy 3ca00000 reg_buf ffffffc03ae38000 [ 0.287484@1] rdma_register success, handle 1 table_size 32768 [ 0.287490@1] set_rdma_handle video rdma handle = 1. [ 0.287542@1] classs created ok [ 0.287554@1] classs file created ok [ 0.487660@1] SCSI subsystem initialized [ 0.487968@1] usbcore: registered new interface driver usbfs [ 0.488039@1] usbcore: registered new interface driver hub [ 0.488123@1] usbcore: registered new device driver usb [ 0.488300@1] pps_core: LinuxPPS API ver. 1 registered [ 0.488310@1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.488336@1] PTP clock support registered [ 0.488913@1] secmon: reserve_mem_size:0x2300000 [ 0.488996@1] secmon secmon: assigned reserved memory node linux,secmon [ 0.490349@1] secmon: get page:ffffffbf00140000, 5000 [ 0.490367@1] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.490372@1] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.490985@1] hdmitx: system: amhdmitx_probe start [ 0.490994@1] hdmitx: system: Ver: 20190815 [ 0.491031@1] hdmitx: system: hdmitx_device.chip_type : 3 [ 0.491090@1] hdmitx: system: not find match pwr-ctl [ 0.491109@1] hdmitx: system: hdmitx_device.drm_feature : 0 [ 0.491135@1] hdmitx: system: hpd irq = 45 [ 0.491143@1] hdmitx: system: vapb_clk failed to probe [ 0.491149@1] hdmitx: system: vpu_clk failed to probe [ 0.491155@1] hdmitx: system: hdcp22_tx_skp failed to probe [ 0.491160@1] hdmitx: system: hdcp22_tx_esm failed to probe [ 0.491165@1] hdmitx: system: venci_top_gate failed to probe [ 0.491170@1] hdmitx: system: venci_0_gate failed to probe [ 0.491175@1] hdmitx: system: venci_0_gate failed to probe [ 0.491788@1] hdmitx: hdmitx20: Mapped PHY: 0xc1109800 [ 0.491806@1] hdmitx: hdmitx20: Mapped PHY: 0xc8834400 [ 0.491815@1] hdmitx: hdmitx20: Mapped PHY: 0xd0100000 [ 0.491837@1] hdmitx: hdmitx20: Mapped PHY: 0xc8100000 [ 0.491844@1] hdmitx: hdmitx20: Mapped PHY: 0xc883c000 [ 0.491849@1] hdmitx: hdmitx20: Mapped PHY: 0xc1104400 [ 0.491855@1] hdmitx: hdmitx20: Mapped PHY: 0xc883a000 [ 0.491861@1] hdmitx: hdmitx20: Mapped PHY: 0xda83a000 [ 0.491871@1] hdmitx: hdmitx20: Mapped PHY: 0xd0044000 [ 0.491882@1] hdmitx: hw: alread display in uboot 0x10 [ 0.491950@1] hdmitx: hw: avmute set to 1 [ 0.491962@1] vout: vout1: register server: hdmitx_vout_server [ 0.491969@1] vout: vout2: register server: hdmitx_vout2_server [ 0.492575@1] hdmitx: system: amhdmitx_probe end [ 0.493428@1] vout: create vout attribute OK [ 0.493602@1] vout: vout_fops_create OK [ 0.493636@1] vout: vout1: register server: nulldisp_vout_server [ 0.493740@1] vout: tvout monitor interval:500(ms), timeout cnt:20 [ 0.493767@1] hdmitx: hdmitx_set_current_vmode[4781] [ 0.493773@1] hdmitx: system: recalc before 1080p60hz 60 1 [ 0.493779@1] hdmitx: system: recalc after 1080p60hz 2997 50 [ 0.493783@1] hdmitx: alread display in uboot [ 0.493787@1] vout: init mode 1080p60hz set ok [ 0.493792@1] vout: aml_tvout_mode_monitor [ 0.493807@1] vout: aml_vout_probe OK [ 0.494725@1] chip type:0x21 [ 0.495266@1] MEMORY:[100000+3ff00000] [ 0.495280@1] ramdump_probe, storage device:data [ 0.495284@1] NO valid ramdump args:0 0 [ 0.495309@1] ramdump_probe, set sticky to 8400 [ 0.495588@1] Advanced Linux Sound Architecture Driver Initialized. [ 0.496693@1] NetLabel: Initializing [ 0.496705@1] NetLabel: domain hash size = 128 [ 0.496709@1] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.496771@1] NetLabel: unlabeled traffic allowed by default [ 0.498707@1] clocksource: Switched to clocksource arch_sys_counter [ 0.589411@0] VFS: Disk quotas dquot_6.6.0 [ 0.589633@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.589988@0] FS-Cache: Loaded [ 0.612325@3] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init. [ 0.613247@3] NET: Registered protocol family 2 [ 0.614375@3] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.614478@3] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 0.614911@3] TCP: Hash tables configured (established 8192 bind 8192) [ 0.615181@3] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.615210@3] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.615631@3] NET: Registered protocol family 1 [ 0.620902@3] RPC: Registered named UNIX socket transport module. [ 0.620944@3] RPC: Registered udp transport module. [ 0.620949@3] RPC: Registered tcp transport module. [ 0.620954@3] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.620988@3] PCI: CLS 0 bytes, default 64 [ 0.621448@0] hdmitx: edid: EDID Parser: [ 0.621460@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621466@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621471@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621506@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621516@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621531@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621536@0] hdmitx: hdmitx: reach vesa idx MAX [ 0.621561@0] [RX]-up_phy_addr = 1 [ 0.621602@0] hdmitx: edid: get dtd0 vic: 16 [ 0.621616@0] hdmitx: edid: find IEEEOUT [ 0.621661@0] hdmitx: edid: check sum valid [ 0.621666@0] hdmitx: edid: check sum valid [ 0.621677@0] hdmitx: edid: check sum valid [ 0.621681@0] hdmitx: edid: check sum valid [ 0.621690@0] hdmitx: edid: blk0 raw data [ 0.621729@0] hdmitx: edid: [ 0.621729@0] 00ffffffffffff001e6df159b37f00000b180103803a1878ea3475a9544e9c26 [ 0.621729@0] 0f5054a54b80714f818081c0a9c0b3000101010101017e4800e0a0381f404040 [ 0.621729@0] 3a00a52221000018023a801871382d40582c4500a5222100001e000000fc004c [ 0.621729@0] 4720554c545241574944450a000000fd00384b1e5a18000a2020202020200112 [ 0.621729@0] [ 0.621729@0] [ 0.621746@0] hdmitx: edid: blk1 raw data [ 0.621783@0] hdmitx: edid: [ 0.621783@0] 02031df14a900403221412051f0113230907078301000065030c001000023a80 [ 0.621783@0] 1871382d40582c450056512100001e011d8018711c1620582c25005651210000 [ 0.621783@0] 9e011d007251d01e206e28550056512100001e8c0ad08a20e02d10103e960056 [ 0.621783@0] 5121000018000000ff003431314e44435230593639310a000000000000000089 [ 0.621783@0] [ 0.621783@0] [ 0.621810@0] hdmitx: system: update rx hdr info 0 [ 0.622673@0] hdmitx: system: irq 80000002 0 [ 0.624562@3] wifi: power_on_pin_OD = 0; [ 0.624622@3] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2 [ 0.624865@3] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok [ 0.624899@3] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok [ 0.624906@3] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup [ 0.624912@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem(): 100.10.545.3 [ 0.625717@3] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok [ 0.625739@3] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=487 [ 0.625746@3] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1 [ 0.625753@3] aml_wifi wifi: [wifi_dev_probe] power_on_pin=486 [ 0.625760@3] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0 [ 0.626863@3] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt [ 0.627176@3] aml_wifi wifi: [wifi_setup_dt] irq num is:(59) [ 0.627196@3] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(487) [ 0.627253@3] aml_wifi wifi: [wifi_setup_dt] power_on_pin(486) [ 0.628052@3] Unpacking initramfs... [ 0.629571@0] hdmitx: system: irq 80000002 0 [ 0.667052@3] Freeing initrd memory: 4988K [ 0.669672@3] hw perfevents: clusterb_enabled = 0 [ 0.669712@3] hw perfevents: cpumasks 0xf, 0x0 [ 0.669787@3] hw perfevents: cluster A irq = 17 [ 0.669970@3] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.676034@3] audit: initializing netlink subsys (disabled) [ 0.676254@3] audit: type=2000 audit(0.628:1): initialized [ 0.678435@3] workingset: timestamp_bits=46 max_order=18 bucket_order=0 [ 0.695117@3] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.696678@3] FS-Cache: Netfs 'nfs' registered for caching [ 0.698308@3] NFS: Registering the id_resolver key type [ 0.698407@3] Key type id_resolver registered [ 0.698413@3] Key type id_legacy registered [ 0.698439@3] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.699205@3] FS-Cache: Netfs 'cifs' registered for caching [ 0.701683@2] SELinux: Registering netfilter hooks [ 0.708199@2] NET: Registered protocol family 38 [ 0.708272@2] Key type asymmetric registered [ 0.708283@2] Asymmetric key parser 'x509' registered [ 0.708987@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.709012@2] io scheduler noop registered (default) [ 0.709020@2] io scheduler deadline registered [ 0.709414@2] io scheduler cfq registered [ 0.717434@2] random: fast init done [ 0.717535@2] random: crng init done [ 0.718246@0] [drm] Initialized [ 0.718561@0] Unable to detect cache hierarchy for CPU 0 [ 0.735049@3] loop: module loaded [ 0.736489@3] mtdoops: mtd device (mtddev=name/number) must be supplied [ 0.738204@3] libphy: Fixed MDIO Bus: probed [ 0.740647@3] ee eth reset:Addr = ffffff800827d408 [ 0.741411@0] meson6-dwmac c9410000.ethernet: no reset control found [ 0.741446@0] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 0.741451@0] Ring mode enabled [ 0.741462@0] DMA HW capability register supported [ 0.741471@0] Normal descriptors [ 0.741476@0] RX Checksum Offload Engine supported [ 0.741480@0] COE Type 2 [ 0.741484@0] TX Checksum insertion supported [ 0.741488@0] Wake-Up On Lan supported [ 0.741610@0] Enable RX Mitigation via HW Watchdog Timer [ 0.745471@2] libphy: stmmac: probed [ 0.745516@2] eth%d: PHY ID 01814400 at 8 IRQ POLL (stmmac-0:08) active [ 0.751017@2] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.751057@2] ehci-pci: EHCI PCI platform driver [ 0.751359@2] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.751478@2] ohci-pci: OHCI PCI platform driver [ 0.753031@2] usbcore: registered new interface driver cdc_acm [ 0.753066@2] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 0.753236@2] usbcore: registered new interface driver usb-storage [ 0.753498@2] usbcore: registered new interface driver usbserial [ 0.753589@2] usbcore: registered new interface driver usbserial_generic [ 0.753667@2] usbserial: USB Serial support registered for generic [ 0.755257@0] mousedev: PS/2 mouse device common for all mice [ 0.756695@3] i2c /dev entries driver [ 0.759684@3] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 0.762276@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 0.767624@0] ledtrig-cpu: registered to indicate activity on CPUs [ 0.769442@0] hidraw: raw HID events driver (C) Jiri Kosina [ 0.770602@0] usbcore: registered new interface driver usbhid [ 0.770634@0] usbhid: USB HID core driver [ 0.772495@0] c81004c0.serial: clock gate not found [ 0.772732@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff80082d14c0 [ 0.772895@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 20, base_baud = 1500000) is a meson_uart [ 0.772939@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200 [ 0.789552@1] clear:20c00000, free:20c00000, tick:267747 us [ 1.141466@0] hdmitx: system: plugin [ 1.270014@0] hdmitx: edid: EDID Parser: [ 1.270018@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270019@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270020@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270033@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270036@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270042@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270044@0] hdmitx: hdmitx: reach vesa idx MAX [ 1.270054@0] [RX]-up_phy_addr = 1 [ 1.270072@0] hdmitx: edid: get dtd0 vic: 16 [ 1.270078@0] hdmitx: edid: find IEEEOUT [ 1.270104@0] hdmitx: edid: check sum valid [ 1.270106@0] hdmitx: edid: check sum valid [ 1.270111@0] hdmitx: edid: check sum valid [ 1.270112@0] hdmitx: edid: check sum valid [ 1.270116@0] hdmitx: edid: blk0 raw data [ 1.270146@0] hdmitx: edid: [ 1.270146@0] 00ffffffffffff001e6df159b37f00000b180103803a1878ea3475a9544e9c26 [ 1.270146@0] 0f5054a54b80714f818081c0a9c0b3000101010101017e4800e0a0381f404040 [ 1.270146@0] 3a00a52221000018023a801871382d40582c4500a5222100001e000000fc004c [ 1.270146@0] 4720554c545241574944450a000000fd00384b1e5a18000a2020202020200112 [ 1.270146@0] [ 1.270146@0] [ 1.270148@0] hdmitx: edid: blk1 raw data [ 1.270177@0] hdmitx: edid: [ 1.270177@0] 02031df14a900403221412051f0113230907078301000065030c001000023a80 [ 1.270177@0] 1871382d40582c450056512100001e011d8018711c1620582c25005651210000 [ 1.270177@0] 9e011d007251d01e206e28550056512100001e8c0ad08a20e02d10103e960056 [ 1.270177@0] 5121000018000000ff003431314e44435230593639310a000000000000000089 [ 1.270177@0] [ 1.270177@0] [ 1.270181@0] hdmitx: system: update physcial size: 580 240 [ 1.272243@0] hdmitx: hdmitx: ddc rd8b error 0x50 0x00 0x00 [ 1.277296@0] hdmitx: system: get current mode: 1080p60hz [ 1.277298@0] hdmitx: system: update physcial size: 580 240 [ 1.277323@0] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16 [ 1.277329@0] hdmitx: system: update rx hdr info 0 [ 1.277333@0] hdmitx: hw: set audio [ 1.277343@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 0, hdev->aud_output_ch = 0 [ 1.277368@0] hdmitx: fs = 0, cd = 4, tmds_clk = 148352 [ 1.277371@0] hdmitx: hw: aud_n_para = 5824 [ 1.277387@0] hdmitx: hw: set channel status [ 2.808852@2] console [ttyS0] enabled [ 2.812957@2] c11084c0.serial: clock gate not found [ 2.817376@2] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff80082d34c0 [ 2.824408@2] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 21, base_baud = 10416666) is a meson_uart [ 2.835027@2] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff80082d5000 [ 2.844561@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port [ 2.851043@2] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff80082d9080 [ 2.865731@2] meson_reset c1104404.reset-controller: can't request region for resource [mem 0xc1104404-0xc1104423] [ 2.871816@2] meson_reset: probe of c1104404.reset-controller failed with error -16 [ 2.880337@2] aml_dma c883e000.aml_dma: Aml dma [ 2.885329@2] aml_aes_dma c883e000.aml_dma:aml_aes: Aml AES_dma [ 2.890482@2] aml_tdes_dma c883e000.aml_dma:aml_tdes: Aml TDES_dma [ 2.896519@2] gpio-keypad gpio_keypad: power key(116) registed. [ 2.901909@2] input: gpio_keypad as /devices/platform/gpio_keypad/input/input0 [ 2.909538@2] efusekeynum: 4 [ 2.911769@2] efusekeyname: mac offset: 0 size: 6 [ 2.918111@2] efusekeyname: mac_bt offset: 6 size: 6 [ 2.924495@2] efusekeyname: mac_wifi offset: 12 size: 6 [ 2.930883@2] efusekeyname: usid offset: 18 size: 16 [ 2.937523@2] efuse efuse: probe OK! [ 2.943583@0] ge2d: ge2d_init_module [ 2.944645@0] ge2d: ge2d_dev major:237 [ 2.948384@0] ge2d: clock source clk_ge2d_gate ffffffc03ae682c0 [ 2.953939@0] ge2d: clock clk_ge2d source ffffffc03ae68cc0 [ 2.959375@0] ge2d: clock source clk_vapb_0 ffffffc03ae68bc0 [ 2.964938@0] ge2d: ge2d init clock is 400000000 HZ, VPU clock is 666666666 HZ [ 2.972160@0] ge2d: ge2d clock is 400 MHZ [ 2.976079@0] ge2d: reserved mem init failed [ 2.980292@0] ge2d: ge2d: pdev=ffffffc03ae49000, irq=48, clk=ffffffc03ae682c0 [ 2.987410@0] ge2d: ge2d start monitor [ 2.991177@1] ge2d: ge2d workqueue monitor start [ 2.991742@0] [tsync_pcr_init]init success. [ 2.992131@0] amvideom vsync irq: 37 [ 2.992180@0] create_ge2d_work_queue video task ok [ 2.993594@0] amvideocap_probe,amvideocap [ 2.993599@0] use cma buf. [ 2.993997@0] fb: osd_init_module [ 2.994525@0] fb: viu vsync irq: 37 [ 2.994569@0] 0x000000db:Y=db,U=0,V=0 [ 2.994571@0] 0x000000dc:Y=dc,U=0,V=0 [ 2.999529@0] dil:err:DI_POST_REG_RD:not attach [ 2.999917@0] fb: osd_rdma_init: rdma_table p=0x3ca08000,op=0x3ca08000 , v=0xffffff80082f7000 [ 2.999960@0] rdma_register, rdma_table_addr ffffff80082f9000 rdma_table_addr_phy 3ca09000 reg_buf ffffffc03ac8a000 [ 2.999964@0] rdma_register success, handle 2 table_size 4096 [ 2.999965@0] fb: osd_rdma_init:osd reset rdma handle = 2. [ 2.999989@0] rdma_register, rdma_table_addr ffffff80082fb000 rdma_table_addr_phy 3ca0a000 reg_buf ffffffc03ac8e000 [ 2.999990@0] rdma_register success, handle 3 table_size 4096 [ 2.999992@0] fb: osd_rdma_init:osd rdma handle = 3. [ 3.000011@0] fb: mem_size: 0x800000 [ 3.000012@0] fb: mem_size: 0x1800000 [ 3.000013@0] fb: mem_size: 0x100000 [ 3.000014@0] fb: mem_size: 0x0 [ 3.000015@0] fb: mem_size: 0x0 [ 3.000022@0] fb: failed to init reserved memory [ 3.000036@0] fb: init fbdev bpp is:32 [ 3.016198@0] dil:err:DI_POST_REG_RD:not attach [ 3.032825@0] dil:err:DI_POST_REG_RD:not attach [ 3.049489@0] dil:err:DI_POST_REG_RD:not attach [ 3.066155@0] dil:err:DI_POST_REG_RD:not attach [ 3.082822@0] dil:err:DI_POST_REG_RD:not attach [ 3.099488@0] dil:err:DI_POST_REG_RD:not attach [ 3.116154@0] dil:err:DI_POST_REG_RD:not attach [ 3.132821@0] dil:err:DI_POST_REG_RD:not attach [ 3.145647@2] fb: set osd0 reverse as NONE [ 3.149503@0] dil:err:DI_POST_REG_RD:not attach [ 3.153691@2] fb: osd probe OK [ 3.156908@2] hdmitx: hdcp: hdmitx_hdcp_init [ 3.161793@2] DI: di_module_init ok. [ 3.164720@2] DI: di_probe: [ 3.166185@0] dil:err:DI_POST_REG_RD:not attach [ 3.171683@2] DI: di_probe: major 511 [ 3.175738@2] deinterlace deinterlace: assigned reserved memory node linux,di_cma [ 3.182744@2] di:flag_cma=1 [ 3.182851@0] dil:err:DI_POST_REG_RD:not attach [ 3.189962@2] DI: CMA size 0x2000000. [ 3.193611@2] pre_irq:51 [ 3.196088@2] post_irq:52 [ 3.198663@2] DI: di_probe allocate rdma channel 0. [ 3.199494@0] dil:err:DI_POST_REG_RD:not attach [ 3.207999@2] 0x000000dd:Y=dd,U=0,V=0 [ 3.211612@2] 0x000000de:Y=de,U=0,V=0 [ 3.215230@2] 0x000000df:Y=df,U=0,V=0 [ 3.216157@0] dil:err:DI_POST_REG_RD:not attach [ 3.223338@2] 0x000000e0:Y=e0,U=0,V=0 [ 3.226960@2] 0x000000e1:Y=e1,U=0,V=0 [ 3.230575@2] 0x000000e2:Y=e2,U=0,V=0 [ 3.232821@0] dil:err:DI_POST_REG_RD:not attach [ 3.238694@2] 0x000000e3:Y=e3,U=0,V=0 [ 3.242305@2] 0x000000f0:Y=f0,U=0,V=0 [ 3.245934@2] 0x000000f1:Y=f1,U=0,V=0 [ 3.249487@0] dil:err:DI_POST_REG_RD:not attach [ 3.254042@2] 0x000000f2:Y=f2,U=0,V=0 [ 3.257668@2] 0x000000f3:Y=f3,U=0,V=0 [ 3.261287@2] 0x000000f4:Y=f4,U=0,V=0 [ 3.264909@2] 0x000000f5:Y=f5,U=0,V=0 [ 3.266154@0] dil:err:DI_POST_REG_RD:not attach [ 3.273017@2] 0x000000f6:Y=f6,U=0,V=0 [ 3.276639@2] 0x000000f7:Y=f7,U=0,V=0 [ 3.280263@2] 0x000000f8:Y=f8,U=0,V=0 [ 3.282821@0] dil:err:DI_POST_REG_RD:not attach [ 3.288371@2] 0x000000f9:Y=f9,U=0,V=0 [ 3.291992@2] 0x000000fa:Y=fa,U=0,V=0 [ 3.295614@2] 0x000000fb:Y=fb,U=0,V=0 [ 3.299237@2] 0x000000fc:Y=fc,U=0,V=0 [ 3.299487@0] dil:err:DI_POST_REG_RD:not attach [ 3.307344@2] 0x000000fd:Y=fd,U=0,V=0 [ 3.310967@2] 0x000000fe:Y=fe,U=0,V=0 [ 3.314584@2] 0x000000ff:Y=ff,U=0,V=0 [ 3.316154@0] dil:err:DI_POST_REG_RD:not attach [ 3.322697@2] 0x0000003a:Y=3a,U=0,V=0 [ 3.326313@2] 0x0000003b:Y=3b,U=0,V=0 [ 3.329944@2] DI: support multi decoding 255~58~59. [ 3.332821@0] dil:err:DI_POST_REG_RD:not attach [ 3.339387@2] DI: di_probe:Di use HRTIMER [ 3.343396@2] DI: di_probe:ok [ 3.346264@2] dim:dim_module_init [ 3.349832@2] dim:dim_module_init finish [ 3.353343@2] dil:dil_init. [ 3.356363@2] dil:dil_init ok. [ 3.359148@2] vdin_drv_init: major 510 [ 3.363259@2] rdma_register, rdma_table_addr ffffff8008422000 rdma_table_addr_phy 3ca0b000 reg_buf ffffffc00a478a00 [ 3.373193@2] rdma_register success, handle 4 table_size 512 [ 3.378771@2] vdin_drv_probe:vdin.0 rdma hanld 4. [ 3.383711@2] [ 3.383711@2] vdin memory resource undefined!! [ 3.389573@2] vdin0 cma_mem_size = 16 MB [ 3.393435@2] vdin0 irq: 53 rdma irq: 2 [ 3.397220@2] set_canvas_manual = 0 [ 3.400713@2] get fclk_div5 err [ 3.403782@2] vdin_drv_probe: vdin cannot get msr clk !!! [ 3.409160@2] vdin_drv_probe: driver initialized ok [ 3.414122@2] rdma_register, rdma_table_addr ffffff8008424000 rdma_table_addr_phy 3ca0c000 reg_buf ffffffc00a478c00 [ 3.424318@2] rdma_register success, handle 5 table_size 512 [ 3.429926@2] vdin_drv_probe:vdin.1 rdma hanld 5. [ 3.434909@2] vdin vdin1: assigned reserved memory node linux,vdin1_cma [ 3.441153@2] [ 3.441153@2] vdin memory resource done. [ 3.446731@2] vdin1 cma_mem_size = 16 MB [ 3.450610@2] vdin1 irq: 54 rdma irq: 4 [ 3.454415@2] set_canvas_manual = 0 [ 3.457884@2] get fclk_div5 err [ 3.460973@2] vdin_drv_probe: vdin cannot get msr clk !!! [ 3.466311@2] vdin_debugfs_init only support debug vdin0 1 [ 3.471747@2] vdin_drv_probe: driver initialized ok [ 3.476660@2] vdin_drv_init: vdin driver init done [ 3.481333@2] [viuin..]viuin_init_module viuin module init [ 3.487143@2] [viuin..]viuin_probe probe ok. [ 3.491740@2] [RX]-hdmirx: hdmirx_init. [ 3.494795@2] ESM HLD: Initializing... [ 3.499604@2] PPMGRDRV: warn: ppmgr module init func called [ 3.504258@2] PPMGRDRV: info: ppmgr_driver_probe called [ 3.509243@2] Reserved memory: failed to init DMA memory pool at 0x000000003d000000, size 0 MiB [ 3.517834@2] PPMGRDRV: info: ppmgr_dev major:508 [ 3.523199@2] aml_vecm_init:module init [ 3.526532@2] [ 3.526532@2] VECM probe start [ 3.531404@2] Can't find detect_colorbar. [ 3.535069@2] Can't find detect_face. [ 3.538756@2] Can't find detect_corn. [ 3.542470@2] Can't find wb_sel. [ 3.545752@2] amlogic, vecm [ 3.548337@2] vlock dt support: 1 [ 3.551615@2] vlock dt new_fsm: 0 [ 3.554882@2] vlock dt hwver: 0 [ 3.557979@2] vlock dt phlock_en: 0 [ 3.561450@2] Can't find vlock_en. [ 3.564887@2] Can't find vlock_mode. [ 3.568514@2] Can't find vlock_pll_m_limit. [ 3.572746@2] Can't find vlock_line_limit. [ 3.576885@2] param_config vlock_en:1 md=0x4 [ 3.581113@2] vlock: maxLine 524,maxPixel 1715 [ 3.585501@2] vlock_status_init vlock_en:1 [ 3.589565@2] aml_vecm_probe: ok [ 3.592846@2] amdolby_vision_init:module init [ 3.598965@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 3.606035@2] meson-mmc: >>>>>>>>hostbase ffffff800842a000, dmode [ 3.611259@2] meson-mmc: gpio_cd = 1c1 [ 3.654726@2] meson-mmc: meson_mmc_probe() : success! [ 3.657015@2] meson-mmc: >>>>>>>>hostbase ffffff8008434000, dmode [ 3.702723@2] meson-mmc: meson_mmc_probe() : success! [ 3.703105@2] amlogic mtd driver init [ 3.706593@2] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0 [ 3.712041@2] input: aml_vkeypad as /devices/platform/rtc/input/input1 [ 3.719584@2] cectx c810023c.aocec: cec driver date:2020/03/16:reduece no msg in sleep time [ 3.719584@2] [ 3.728523@2] cectx c810023c.aocec: compatible:amlogic, amlogic-aocec [ 3.734629@2] cectx c810023c.aocec: cecb_ver:0x0 [ 3.739173@2] cectx c810023c.aocec: line_reg:0x0 [ 3.743773@2] cectx c810023c.aocec: line_bit:0x8 [ 3.748313@2] cectx c810023c.aocec: ee_to_ao:0x0 [ 3.753057@2] input: cec_input as /devices/virtual/input/input2 [ 3.758971@2] cectx c810023c.aocec: not find 'port_num' [ 3.763950@2] cectx c810023c.aocec: using cec:0 [ 3.768426@2] cectx c810023c.aocec: get sleep state error! [ 3.773888@2] cectx c810023c.aocec: no hdmirx regs [ 3.778588@2] cectx c810023c.aocec: no hhi regs [ 3.783073@2] cectx c810023c.aocec: no periphs regs [ 3.787907@2] cectx c810023c.aocec: not find 'output' [ 3.796035@2] irq cnt:1, a:46, b46 [ 3.796922@2] cectx c810023c.aocec: wakeup_reason:0x0 [ 3.801375@2] cectx c810023c.aocec: cev val1: 0x0;val2: 0x0 [ 3.806794@2] cectx c810023c.aocec: aml_cec_probe success end [ 3.812820@2] unifykey: storage in base: 0xffffffc005000000 [ 3.818023@2] unifykey: storage out base: 0xffffffc005040000 [ 3.823618@2] unifykey: storage block base: 0xffffffc005080000 [ 3.829424@2] unifykey: probe done! [ 3.833743@2] unifykey: no efuse-version set, use default value: -1 [ 3.839072@2] unifykey: key unify config unifykey-num is 16 [ 3.844654@2] unifykey: key unify fact unifykey-num is 16 [ 3.849926@2] unifykey: unifykey_devno: 1f800000 [ 3.854794@2] unifykey: device unifykeys created ok [ 3.859469@2] unifykey: aml_unifykeys_init done! [ 3.864254@2] audio_dsp: [dsp]register dsp to char divece(257) [ 3.870295@2] amaudio: amaudio: driver amaudio init! [ 3.875134@2] amaudio: amaudio_init - amaudio: driver amaudio succuess! [ 3.881726@2] sysled: module init [ 3.884904@2] meson_wdt c11098d0.watchdog: start watchdog [ 3.889803@2] meson_wdt c11098d0.watchdog: creat work queue for watch dog [ 3.896848@2] meson_wdt c11098d0.watchdog: AML Watchdog Timer probed done [ 3.904458@2] amlogic rfkill init [ 3.906676@2] enter bt_probe of_node [ 3.910092@2] not get gpio_en [ 3.912991@2] not get gpio_hostwake [ 3.916409@2] not get gpio_btwakeup [ 3.919865@2] power on valid level is high [ 3.923741@2] bt: power_on_pin_OD = 0; [ 3.927448@2] bt: power_off_flag = 1; [ 3.931075@2] dis power down = 0; [ 3.958857@2] request_irq error ret=-22 [ 3.958918@2] dev_pm_set_wake_irq failed: -22 [ 3.963474@2] dmc_monitor_probe [ 3.965151@2] defendkey c8834500.defendkey: Reserved memory is not enough! [ 3.971369@2] defendkey: probe of c8834500.defendkey failed with error -22 [ 3.979369@2] bl301_manager: driver init [ 3.982015@2] bl301_manager: IR remote wake-up code: 0xffffffff [ 3.987895@2] bl301_manager: IR remote wake-up code mask: 0xffffffff [ 3.994167@2] bl301_manager: IR remote wake-up code protocol: 0x0 [ 4.000224@2] bl301_manager: enable 5V system power on suspend/power off state: 0 [ 4.015715@2] usbcore: registered new interface driver snd-usb-audio [ 4.017996@2] aml_codec_T9015 c8832000.t9015: aml_T9015_audio_codec_probe [ 4.023233@2] T9015 acodec used by meson, tdmout:0 [ 4.029628@2] snd_i2s_dai: clock source gate top_glue : ffffffc00a41c100 [ 4.034609@2] snd_i2s_dai: clock source gate aud_buf : ffffffc00a41c180 [ 4.041156@2] snd_i2s_dai: clock source gate i2s_out : ffffffc00a41c200 [ 4.047697@2] snd_i2s_dai: clock source gate amclk_measure : ffffffc00a41c280 [ 4.055167@2] snd_i2s_dai: clock source gate aififo2 : ffffffc00a41c300 [ 4.061340@2] snd_i2s_dai: clock source gate aud_mixer : ffffffc00a41c380 [ 4.068089@2] snd_i2s_dai: clock source gate mixer_reg : ffffffc00a41c400 [ 4.074800@2] snd_i2s_dai: clock source gate adc : ffffffc00a41c480 [ 4.081005@2] snd_i2s_dai: clock source gate top_level : ffffffc00a41c500 [ 4.087755@2] snd_i2s_dai: clock source gate aoclk : ffffffc00a41c580 [ 4.094458@2] snd_i2s_dai: clock source gate aud_in : ffffffc00a41c600 [ 4.100548@2] snd_i2s_dai: ignore aud_buf/vdac_clk gate [ 4.105937@2] aml-i2s-dai I2S: I2S Mic is in platform! [ 4.111717@2] snd_pcm_dai: pcm mode detection =1 [ 4.115670@2] snd_pcm_dai: tdm config: 0x0, 0x0, 0, 0 [ 4.121002@2] snd_spdif_dai: enterd aml_spdif_play,set_clock:-1,sample_rate=4 [ 4.127995@2] snd_spdif_dai: set normal 512 fs /4 fs [ 4.132383@2] snd_spdif_dai: set 958 audio clk div 4 [ 4.137286@2] hdmitx: audio: aout notify format CT_PCM [ 4.142377@2] hdmitx: hw: set audio [ 4.145830@2] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 4.155076@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 4.160218@2] hdmitx: hw: aud_n_para = 5824 [ 4.164728@2] hdmitx: hw: set channel status [ 4.168631@2] hdmitx: audio: Audio Type: PCM [ 4.172823@2] hdmitx: audio: set audio param [ 4.177584@2] snd_dmic d0042000.snd_dmic: Dmic probe! [ 4.182172@2] periphs-banks:474 is using the pin GPIODV_24 as gpio [ 4.188187@2] meson-gxl-pinctrl pinctrl@4b0: request() failed for pin 73 [ 4.194840@2] meson-gxl-pinctrl pinctrl@4b0: pin-73 (d0042000.snd_dmic) status -22 [ 4.202684@2] meson-gxl-pinctrl pinctrl@4b0: could not request pin 73 (GPIODV_24) from group dmic_in_dv24 on device pinctrl-meson [ 4.213962@2] snd_dmic d0042000.snd_dmic: Error applying setting, reverse things back [ 4.221722@2] snd_dmic d0042000.snd_dmic: pinctrls error! [ 4.227093@2] snd_dmic: probe of d0042000.snd_dmic failed with error -22 [ 4.234237@2] spdif-dit spdif_codec: audio_spdif_out_mute can't get pinctrl [ 4.241070@2] spdif-dit spdif_codec: audio_spdif_in_mute can't get pinctrl [ 4.247427@2] spdif-dit spdif_codec: audio_spdif_in can't get pinctrl [ 4.254480@2] snd_card_meson: aml_card_dai_parse_of codec_node count:1 [ 4.260429@2] snd_card_meson: aml_card_dai_parse_of codec_node count:1 [ 4.266852@2] snd_card_meson: aml_card_dai_parse_of codec_node count:1 [ 4.478928@2] snd_card_meson: headphone detection disable=1 [ 4.478959@2] snd_card_meson: no spk event delay time set [ 4.485479@2] aml_meson_snd_card aml_sound_meson: T9015-audio-hifi <-> I2S mapping ok [ 4.493462@2] aml_meson_snd_card aml_sound_meson: dit-hifi <-> SPDIF mapping ok [ 4.499360@2] snd_pcm: enter aml_pcm_new dai->name: PCM dai->id: 0 [ 4.505962@2] aml_meson_snd_card aml_sound_meson: pcm2bt-pcm <-> PCM mapping ok [ 4.512691@2] aml_meson_snd_card aml_sound_meson: ASoC: no source widget found for LOUTL [ 4.520633@2] aml_meson_snd_card aml_sound_meson: ASoC: Failed to add route LOUTL -> direct -> Ext Spk [ 4.530196@2] aml_meson_snd_card aml_sound_meson: ASoC: no source widget found for LOUTR [ 4.537872@2] aml_meson_snd_card aml_sound_meson: ASoC: Failed to add route LOUTR -> direct -> Ext Spk [ 4.547296@2] aml-spdif-dai SPDIF: ASoC: Failed to create S/PDIF Playback debugfs file [ 4.554966@2] aml-spdif-dai SPDIF: ASoC: Failed to create S/PDIF Capture debugfs file [ 4.564371@2] snd_card_meson: enable i2sclk in startup [ 4.572573@2] Register vad [ 4.573664@2] NET: Registered protocol family 10 [ 4.576183@2] NET: Registered protocol family 17 [ 4.579730@2] Key type dns_resolver registered [ 4.585229@2] Registered swp emulation handler [ 4.588442@2] Registered cp15_barrier emulation handler [ 4.593610@2] Registered setend emulation handler [ 4.598300@2] disable EAS feature [ 4.602593@1] registered taskstats version 1 [ 4.612728@3] dwc3 c9000000.dwc3: Configuration mismatch. dr_mode forced to host [ 4.649540@0] vpu: switch_vpu_mem_pd: unsupport vpu mod: 12 [ 5.118374@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.118444@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.126588@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x02010010 [ 5.135046@3] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0xc9000000 [ 5.141138@3] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.147906@3] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.155228@3] usb usb1: Product: xHCI Host Controller [ 5.160233@3] usb usb1: Manufacturer: Linux 4.9.113 xhci-hcd [ 5.165837@3] usb usb1: SerialNumber: xhci-hcd.0.auto [ 5.171489@0] hub 1-0:1.0: USB hub found [ 5.174805@0] hub 1-0:1.0: 2 ports detected [ 5.179191@0] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.184592@0] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.192320@0] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.200587@0] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 5.207325@0] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.214657@0] usb usb2: Product: xHCI Host Controller [ 5.219698@0] usb usb2: Manufacturer: Linux 4.9.113 xhci-hcd [ 5.225269@0] usb usb2: SerialNumber: xhci-hcd.0.auto [ 5.230901@1] hub 2-0:1.0: USB hub found [ 5.234186@1] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 5.241466@1] usb usb2: Unsupported the hub [ 5.245982@1] aml_vrtc rtc: setting system clock to 2020-10-21 08:36:33 UTC (1603269393) [ 5.253997@1] dwc_otg c9100000.dwc2_a: dwc_otg_driver_probe(ffffffc03adbf000) [ 5.254030@1] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: d0078000, ctrl: 0 [ 5.262168@1] dwc_otg_driver_probe host only, not probe usb_otg!!! [ 5.270447@0] cpucore_cooling_register, max_cpu_core_num:4 [ 5.279677@0] gxbb_pm: enter meson_pm_probe! [ 5.279722@0] gxbb_pm: system suspend level: 1 [ 5.282975@0] no vddio3v3_en pin [ 5.285748@0] pm-meson aml_pm: Can't get switch_clk81 [ 5.290809@0] gxbb_pm: meson_pm_probe done [ 5.295261@0] ALSA device list: [ 5.297894@0] #0: AML-MESONAUDIO [ 5.301556@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 115200 to 115200 [ 5.306802@0] Freeing unused kernel memory: 4800K [ 5.363964@1] vout: vmode set to null [ 5.364053@1] fb: current vmode=1080p60hz, cmd: 0x10000 [ 5.367215@1] vlock: event MODE_CHANGE_PRE 0 [ 5.371511@1] vout: new mode null set ok [ 5.375295@1] DOLBY: vout_notify_callback: VOUT_EVENT_MODE_CHANGE [ 5.381339@1] fb: current vmode=null, cmd: 0x20000 [ 5.386398@1] vout: vmode set to 1080p60hz [ 5.390274@1] fb: current vmode=null, cmd: 0x10000 [ 5.394911@1] hdmitx: hdmitx_set_current_vmode[4781] [ 5.399794@1] hdmitx: system: recalc before 1080p60hz 2997 50 [ 5.405484@1] hdmitx: system: recalc after 1080p60hz 2997 50 [ 5.411098@1] hdmitx: system: get current mode: 1080p60hz [ 5.416438@1] hdmitx: system: update physcial size: 580 240 [ 5.422004@1] hdmitx: video: already init VIC = 0 Now VIC = 16 [ 5.427823@1] hdmitx: hw: div40: 0 [ 5.458933@0] hdmitx: system: irq 80000001 0 [ 5.460718@1] hdmitx: ddc w1b error 0x54 0x20 0x00 [ 5.462315@1] hdmitx: frac_rate = 1 [ 5.465772@1] hdmitx: hdmitx: set clk: VIC = 16 cd = 4 cs = 2 frac_rate = 1 [ 5.472845@1] hdmitx: config HPLL = 5940000 frac_rate = 1 [ 5.478242@1] hdmitx: HPLL: 0xc000027b [ 5.481895@1] hdmitx: config HPLL done [ 5.485610@1] hdmitx: set_hpll_od3_clk_div[643] div = 6 [ 5.490784@1] hdmitx: j = 4 vid_clk_div = 1 [ 5.495017@1] hdmitx: set enc for VIC: 16 [ 5.498990@0] hdmitx: system: irq 80000001 0 [ 5.514718@0] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 5.538712@1] hdmitx: hw: config hdmitx IP vic = 16 cd:4 cs: 2 [ 5.549163@1] hdmitx: video: Sink is HDMI device [ 5.549247@1] hdmitx: hw: set audio [ 5.551605@1] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 5.560845@1] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 5.566048@1] hdmitx: hw: aud_n_para = 5824 [ 5.570180@1] hdmitx: [0x10000104]: 0x00000001 [ 5.570189@1] hdmitx: [0x10000180]: 0x000000ff [ 5.570191@1] hdmitx: [0x10000181]: 0x000000ff [ 5.570194@1] hdmitx: [0x10000182]: 0x00000003 [ 5.570196@1] hdmitx: [0x10000183]: 0x00000007 [ 5.570199@1] hdmitx: [0x10000184]: 0x0000003f [ 5.570202@1] hdmitx: [0x10000185]: 0x00000002 [ 5.570206@1] hdmitx: [0x10000187]: 0x000000ff [ 5.570208@1] hdmitx: [0x10000188]: 0x00000003 [ 5.609744@1] hdmitx: hw: set channel status [ 5.614005@1] hdmitx: audio: Audio Type: PCM [ 5.618202@1] hdmitx: system: update rx hdr info 0 [ 5.622928@1] vout: new mode 1080p60hz set ok [ 5.627238@1] DOLBY: vout_notify_callback: VOUT_EVENT_MODE_CHANGE [ 5.633275@1] fb: current vmode=1080p60hz, cmd: 0x20000 [ 5.638460@1] vlock: event MODE_CHANGE [ 5.642235@1] vout: aml_tvout_mode_work: monitor stop [ 5.645763@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 5.645773@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 5.645826@0] fb: use ion buffer for fb memory, fb_index=0 [ 5.645847@0] ion_dev ion_dev: Fail to allocate buffer [ 5.645852@0] fb: malloc_osd_memory: size=1800000, FAILED. [ 5.649211@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 5.649219@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 5.649253@0] fb: use ion buffer for fb memory, fb_index=1 [ 5.649279@0] ion_dev ion_dev: Fail to allocate buffer [ 5.649455@0] fb: malloc_osd_memory: size=100000, FAILED. [ 5.666683@0] VID: VD1 off [ 5.666919@0] usb 1-1: New USB device found, idVendor=05e3, idProduct=0736 [ 5.666924@0] usb 1-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2 [ 5.666927@0] usb 1-1: Product: USB Storage [ 5.666930@0] usb 1-1: Manufacturer: Generic [ 5.666932@0] usb 1-1: SerialNumber: 000000000272 [ 5.671857@0] usb-storage 1-1:1.0: USB Mass Storage device detected [ 5.672400@0] scsi host0: usb-storage 1-1:1.0 [ 5.744646@2] fb: osd[0] enable: 1 (sh) [ 5.751464@0] fb: osd[1] enable: 0 (sh) [ 5.786401@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 5.786405@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 5.786407@3] fb: use ion buffer for fb memory, fb_index=0 [ 5.786423@3] ion_dev ion_dev: Fail to allocate buffer [ 5.786427@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 5.789784@2] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 5.789793@2] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 5.789796@2] fb: use ion buffer for fb memory, fb_index=0 [ 5.789811@2] ion_dev ion_dev: Fail to allocate buffer [ 5.789815@2] fb: malloc_osd_memory: size=1800000, FAILED. [ 5.791368@1] Checking disk(s): LABEL=COREELEC LABEL=STORAGE [ 6.406710@2] lcd vlock_en=1, vlock_mode=0x4 [ 6.672007@1] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0272 PQ: 0 ANSI: 0 [ 6.673220@0] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 6.738855@1] sd 0:0:0:0: [sda] 30375936 512-byte logical blocks: (15.6 GB/14.5 GiB) [ 6.739717@1] sd 0:0:0:0: [sda] Write Protect is off [ 6.739723@1] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08 [ 6.740559@1] sd 0:0:0:0: [sda] No Caching mode page found [ 6.740563@1] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 6.745063@1] sda: sda1 sda2 [ 6.747863@1] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 7.201787@0] fsck: CP437: Invalid argument [ 7.201905@0] fsck: fsck.fat 4.1 (2017-01-24) [ 7.202047@0] fsck: /dev/sda1: 71 files, 27219/65501 clusters [ 7.202222@0] fsck: STORAGE: clean, 652/3665920 files, 471835/14659584 blocks [ 7.272444@2] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 7.272454@2] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 7.272456@2] fb: use ion buffer for fb memory, fb_index=0 [ 7.272472@2] ion_dev ion_dev: Fail to allocate buffer [ 7.272477@2] fb: malloc_osd_memory: size=1800000, FAILED. [ 7.410877@1] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 7.410884@1] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 7.410886@1] fb: use ion buffer for fb memory, fb_index=0 [ 7.410902@1] ion_dev ion_dev: Fail to allocate buffer [ 7.410907@1] fb: malloc_osd_memory: size=1800000, FAILED. [ 7.559628@1] EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities [ 7.560665@1] EXT4-fs (sda2): couldn't mount as ext2 due to feature incompatibilities [ 7.613185@1] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 7.718362@0] ### BIG FAT WARNING [ 7.718408@0] ### sda2 is removable. suspend/resume may not work [ 7.722410@2] ### BIG FAT WARNING [ 7.722456@2] ### sda1 is removable. suspend/resume may not work [ 8.221029@3] cgroup: cgroup2: unknown option "nsdelegate" [ 8.228507@3] systemd[1]: systemd 242 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD +IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 8.229155@3] systemd[1]: Detected architecture arm64. [ 8.234451@3] systemd[1]: Set hostname to . [ 8.298355@3] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 8.298369@3] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 8.411397@3] systemd[1]: Starting Show Version... [ 8.413018@3] systemd[1]: Created slice User and Session Slice. [ 8.414255@3] systemd[1]: Listening on Journal Socket (/dev/log). [ 8.415386@3] systemd[1]: Listening on Journal Socket. [ 8.419078@3] systemd[1]: Mounting POSIX Message Queue File System... [ 8.583699@0] kernel-overlays-setup: setup base modules [ 8.683371@1] kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/4.9.113 [ 8.743176@1] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware [ 8.743356@1] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays [ 8.744769@1] kernel-overlays-setup: done [ 8.958465@2] media: Linux media interface: v0.10 [ 9.000443@3] Linux video capture interface: v2.00 [ 9.046266@0] amlvid:info: amlvideo_init called [ 9.046274@0] amlvid:info: amlvideo_create_instance called [ 9.046282@0] amlvid:info: v4l2_dev.name=:amlvideo-000 [ 9.046613@3] amlvideo-000: V4L2 device registered as video10 [ 9.046622@3] amlvid:info: amlvideo_create_instance called [ 9.046625@3] amlvid:info: v4l2_dev.name=:amlvideo-001 [ 9.047018@3] amlvideo-001: V4L2 device registered as video23 [ 9.058196@3] systemd-journald[2231]: Received request to flush runtime journal from PID 1 [ 9.078007@2] media_clock: loading out-of-tree module taints kernel. [ 9.080084@2] register clk_set_setting cpu[33] [ 9.081807@3] Registered firmware driver success. [ 9.083209@3] Try to load video/h264_enc.bin ... [ 9.083318@3] load firmware size : 76288, Name : video/h264_enc.bin. [ 9.084596@3] Try to load video/video_ucode.bin ... [ 9.086605@3] load firmware size : 1816576, Name : video/video_ucode.bin. [ 9.122484@2] Amlogic A/V streaming port init [ 9.127506@3] get gate demux control ok ffffffc039d38c00 [ 9.127524@3] get gate parser_top control ok ffffffc039d38b80 [ 9.127542@3] get gate vdec control ok ffffffc039d38b00 [ 9.127552@3] get gate clk_81 control failed (null) [ 9.127576@3] get gate clk_vdec_mux control ok ffffffc039d38a80 [ 9.127603@3] get gate clk_hcodec_mux control ok ffffffc039d38800 [ 9.127633@3] get gate clk_hevc_mux control ok ffffffc039d38880 [ 9.127638@3] get gate clk_hevcb_mux control failed (null) [ 9.127642@3] get gate ahbarb0 control failed (null) [ 9.127646@3] get gate asyncfifo control failed (null) [ 9.168865@3] amvdec_avs module init [ 9.192523@0] ammvdec_avs module init [ 9.199948@0] amvdec_h264 module init [ 9.216660@0] amvdec_h265 module init [ 9.230166@0] ammvdec_h264 module init [ 9.334622@3] ammvdec_mpeg12 module init [ 9.342574@3] ammvdec_mpeg4_driver_init_module [ 9.373579@2] decoder registered as /dev/video26 [ 9.381485@2] amvdec_vc1 module init [ 9.388334@2] amvdec_vp9 module init [ 9.414029@2] Triggered SDIO WiFi power on and bus rescan. [ 9.414056@2] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 486 [ 9.742811@2] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 486 [ 10.064432@0] meson-mmc: sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff [ 10.064441@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 10.064480@3] meson-mmc: meson_mmc_irq_thread 2779 sdio: cmd:52 [ 10.065543@0] meson-mmc: sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff [ 10.065550@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 10.065576@3] meson-mmc: meson_mmc_irq_thread 2779 sdio: cmd:52 [ 10.070227@0] meson-mmc: sdio: resp_timeout,vstat:0xa3ff2800,virqc:3fff [ 10.070234@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8 [ 10.070256@3] meson-mmc: meson_mmc_irq_thread 2779 sdio: cmd:8 [ 10.088438@2] sdio: new high speed SDIO card at address 0001 [ 10.088447@0] sdio: clock 50000000, 4-bit-bus-width [ 10.088447@0] [ 10.088822@0] meson-mmc: [sdio_reinit] finish [ 10.146124@0] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information. [ 10.146131@0] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 11.527379@3] mali-utgard d00c0000.mali: set min pp to default 1 [ 11.527389@3] mali-utgard d00c0000.mali: set min clk default to 0 [ 11.527560@3] mali-utgard d00c0000.mali: max clk set 2 [ 11.527570@3] mali-utgard d00c0000.mali: turbo clk set to 3 [ 11.530944@3] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-gpufreq-0 failed:-22 [ 11.530959@3] gpu cooling register okay with err=0 [ 11.533756@2] gpu core cooling register okay with err=0 [ 11.534181@2] Mali: Mali device driver loaded [ 11.648046@0] [0] vcodec_dec decoder [ 11.648364@0] [0] release decoder [ 12.300157@1] internal phy init [ 12.372114@0] internal phy init [ 12.386364@0] meson6-dwmac c9410000.ethernet eth0: fail to init PTP. [ 12.386923@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 13.244809@1] Registered IR keymap rc-empty [ 13.246541@2] input: meson-ir as /devices/platform/c8100580.meson-ir/rc/rc0/input3 [ 13.247212@2] rc rc0: meson-ir as /devices/platform/c8100580.meson-ir/rc/rc0 [ 13.248096@3] meson-ir c8100580.meson-ir: AO_RTI_PIN_MUX : 0x509801 [ 13.248113@3] meson-ir c8100580.meson-ir: receiver initialized [ 13.269749@2] lirc_dev: IR Remote Control driver registered, major 501 [ 13.283047@3] rc rc0: lirc_dev: driver ir-lirc-codec (meson-ir) registered at minor = 0 [ 13.283060@3] IR LIRC bridge handler initialized [ 13.355634@0] IR NEC protocol handler initialized [ 13.386617@1] IR RC6 protocol handler initialized [ 13.390870@0] wol_reg12[12]==0, error [ 14.415777@0] meson6-dwmac c9410000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off [ 14.415810@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 14.475848@1] 8021q: 802.1Q VLAN Support v1.8 [ 15.023032@0] the demux clock on, ref cnt: 1 [ 15.023043@0] the parser_top clock on, ref cnt: 1 [ 15.023046@0] the vdec clock on, ref cnt: 1 [ 15.023071@0] the clk_hevc_mux clock on, ref cnt: 1 [ 15.023082@0] hevc mux clock is 500000000 Hz [ 15.023111@0] the clk_vdec_mux clock on, ref cnt: 1 [ 15.023117@0] vdec mux clock is 500000000 Hz [ 15.023199@0] vdec_create instance ffffff800c1dd000, total 1 [ 15.023216@0] vdec_disable_DMC input->target= 0x0 [ 15.023219@0] vdec_release instance ffffff800c1dd000, total 1 [ 15.023243@0] the clk_vdec_mux clock off, ref cnt: 0 [ 15.023246@0] the vdec clock off, ref cnt: 0 [ 15.023250@0] the parser_top clock off, ref cnt: 0 [ 15.023252@0] the demux clock off, ref cnt: 0 [ 15.605210@3] snd_spdif_dai: enterd aml_spdif_play,set_clock:4,sample_rate=4 [ 15.605242@3] snd_spdif_dai: set 958 audio clk div 2 [ 15.636682@0] audio_dsp: buf=0 [ 15.636693@0] audio_dsp: IEC958_mode_raw=0 [ 15.636738@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 15.636740@0] audio_dsp: last mode 0,now 0 [ 15.642622@0] snd_spdif_dai: set normal 512 fs /4 fs [ 15.642633@0] snd_spdif_dai: set 958 audio clk div 4 [ 15.642829@0] hdmitx: hw: set audio [ 15.642833@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 15.642860@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 15.642863@0] hdmitx: hw: aud_n_para = 8918 [ 15.642880@0] hdmitx: hw: set channel status [ 15.642937@0] hdmitx: audio: Audio Type: PCM [ 15.642939@0] hdmitx: audio: set audio param [ 15.643209@3] snd_spdif_dai: set normal 512 fs /4 fs [ 15.702325@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 15.702337@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 15.702339@0] fb: use ion buffer for fb memory, fb_index=0 [ 15.702353@0] ion_dev ion_dev: Fail to allocate buffer [ 15.702357@0] fb: malloc_osd_memory: size=1800000, FAILED. [ 15.719193@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 15.719206@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 15.719208@0] fb: use ion buffer for fb memory, fb_index=0 [ 15.719223@0] ion_dev ion_dev: Fail to allocate buffer [ 15.719228@0] fb: malloc_osd_memory: size=1800000, FAILED. [ 19.115083@3] the demux clock on, ref cnt: 1 [ 19.115095@3] the parser_top clock on, ref cnt: 1 [ 19.115099@3] the vdec clock on, ref cnt: 1 [ 19.115121@3] the clk_vdec_mux clock on, ref cnt: 1 [ 19.115134@3] vdec mux clock is 500000000 Hz [ 19.115202@3] vdec_create instance ffffff800c1fe000, total 1 [ 19.115218@3] vdec_disable_DMC input->target= 0x0 [ 19.115221@3] vdec_release instance ffffff800c1fe000, total 1 [ 19.115246@3] the clk_vdec_mux clock off, ref cnt: 0 [ 19.115250@3] the vdec clock off, ref cnt: 0 [ 19.115253@3] the parser_top clock off, ref cnt: 0 [ 19.115256@3] the demux clock off, ref cnt: 0 [ 19.263097@3] snd_spdif_dai: enterd aml_spdif_play,set_clock:5,sample_rate=4 [ 19.263120@3] snd_spdif_dai: set 958 audio clk div 2 [ 19.263133@3] hdmitx: hw: set audio [ 19.263137@3] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 19.263165@3] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 19.263167@3] hdmitx: hw: aud_n_para = 5824 [ 19.263184@3] hdmitx: hw: set channel status [ 19.263236@3] hdmitx: audio: Audio Type: PCM [ 19.263238@3] hdmitx: audio: set audio param [ 19.294064@0] audio_dsp: buf=0 [ 19.294074@0] audio_dsp: IEC958_mode_raw=0 [ 19.294120@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 19.294122@0] audio_dsp: last mode 0,now 0 [ 19.299985@0] snd_spdif_dai: set normal 512 fs /4 fs [ 19.299995@0] snd_spdif_dai: set 958 audio clk div 4 [ 19.300008@0] hdmitx: hw: set audio [ 19.300012@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 19.300041@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 19.300043@0] hdmitx: hw: aud_n_para = 8918 [ 19.300060@0] hdmitx: hw: set channel status [ 19.300112@0] hdmitx: audio: Audio Type: PCM [ 19.300114@0] hdmitx: audio: set audio param [ 19.300392@3] snd_spdif_dai: set normal 512 fs /4 fs [ 19.349531@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 19.349542@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 19.349545@3] fb: use ion buffer for fb memory, fb_index=0 [ 19.349559@3] ion_dev ion_dev: Fail to allocate buffer [ 19.349563@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 19.353397@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 19.353408@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 19.353411@3] fb: use ion buffer for fb memory, fb_index=0 [ 19.353425@3] ion_dev ion_dev: Fail to allocate buffer [ 19.353430@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 22.372813@3] the demux clock on, ref cnt: 1 [ 22.372825@3] the parser_top clock on, ref cnt: 1 [ 22.372828@3] the vdec clock on, ref cnt: 1 [ 22.372851@3] the clk_vdec_mux clock on, ref cnt: 1 [ 22.372863@3] vdec mux clock is 500000000 Hz [ 22.372935@3] vdec_create instance ffffff800c21b000, total 1 [ 22.372952@3] vdec_disable_DMC input->target= 0x0 [ 22.372955@3] vdec_release instance ffffff800c21b000, total 1 [ 22.372979@3] the clk_vdec_mux clock off, ref cnt: 0 [ 22.372983@3] the vdec clock off, ref cnt: 0 [ 22.372986@3] the parser_top clock off, ref cnt: 0 [ 22.372989@3] the demux clock off, ref cnt: 0 [ 22.521397@0] snd_spdif_dai: enterd aml_spdif_play,set_clock:5,sample_rate=4 [ 22.521422@0] snd_spdif_dai: set 958 audio clk div 2 [ 22.521435@0] hdmitx: hw: set audio [ 22.521438@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 22.521467@0] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 22.521470@0] hdmitx: hw: aud_n_para = 5824 [ 22.521486@0] hdmitx: hw: set channel status [ 22.521539@0] hdmitx: audio: Audio Type: PCM [ 22.521541@0] hdmitx: audio: set audio param [ 22.552858@3] audio_dsp: buf=0 [ 22.552868@3] audio_dsp: IEC958_mode_raw=0 [ 22.552916@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 22.552918@3] audio_dsp: last mode 0,now 0 [ 22.558642@3] snd_spdif_dai: set normal 512 fs /4 fs [ 22.558653@3] snd_spdif_dai: set 958 audio clk div 4 [ 22.558666@3] hdmitx: hw: set audio [ 22.558670@3] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 22.558783@3] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 22.558786@3] hdmitx: hw: aud_n_para = 8918 [ 22.558804@3] hdmitx: hw: set channel status [ 22.558861@3] hdmitx: audio: Audio Type: PCM [ 22.558863@3] hdmitx: audio: set audio param [ 22.559116@1] snd_spdif_dai: set normal 512 fs /4 fs [ 22.608077@1] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 22.608088@1] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 22.608091@1] fb: use ion buffer for fb memory, fb_index=0 [ 22.608105@1] ion_dev ion_dev: Fail to allocate buffer [ 22.608109@1] fb: malloc_osd_memory: size=1800000, FAILED. [ 22.611823@1] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 22.611834@1] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 22.611836@1] fb: use ion buffer for fb memory, fb_index=0 [ 22.611858@1] ion_dev ion_dev: Fail to allocate buffer [ 22.611862@1] fb: malloc_osd_memory: size=1800000, FAILED. [ 25.618179@3] the demux clock on, ref cnt: 1 [ 25.618190@3] the parser_top clock on, ref cnt: 1 [ 25.618193@3] the vdec clock on, ref cnt: 1 [ 25.618216@3] the clk_vdec_mux clock on, ref cnt: 1 [ 25.618228@3] vdec mux clock is 500000000 Hz [ 25.618292@3] vdec_create instance ffffff800c238000, total 1 [ 25.618309@3] vdec_disable_DMC input->target= 0x0 [ 25.618312@3] vdec_release instance ffffff800c238000, total 1 [ 25.618338@3] the clk_vdec_mux clock off, ref cnt: 0 [ 25.618342@3] the vdec clock off, ref cnt: 0 [ 25.618345@3] the parser_top clock off, ref cnt: 0 [ 25.618348@3] the demux clock off, ref cnt: 0 [ 25.766334@2] snd_spdif_dai: enterd aml_spdif_play,set_clock:5,sample_rate=4 [ 25.766359@2] snd_spdif_dai: set 958 audio clk div 2 [ 25.766372@2] hdmitx: hw: set audio [ 25.766376@2] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 25.766405@2] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 25.766407@2] hdmitx: hw: aud_n_para = 5824 [ 25.766424@2] hdmitx: hw: set channel status [ 25.766476@2] hdmitx: audio: Audio Type: PCM [ 25.766478@2] hdmitx: audio: set audio param [ 25.797929@3] audio_dsp: buf=0 [ 25.797939@3] audio_dsp: IEC958_mode_raw=0 [ 25.797981@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 25.797984@3] audio_dsp: last mode 0,now 0 [ 25.803773@3] snd_spdif_dai: set normal 512 fs /4 fs [ 25.803783@3] snd_spdif_dai: set 958 audio clk div 4 [ 25.803796@3] hdmitx: hw: set audio [ 25.803800@3] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 25.803829@3] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 25.803831@3] hdmitx: hw: aud_n_para = 8918 [ 25.803848@3] hdmitx: hw: set channel status [ 25.803900@3] hdmitx: audio: Audio Type: PCM [ 25.803902@3] hdmitx: audio: set audio param [ 25.804168@0] snd_spdif_dai: set normal 512 fs /4 fs [ 25.853736@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 25.853746@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 25.853748@0] fb: use ion buffer for fb memory, fb_index=0 [ 25.853763@0] ion_dev ion_dev: Fail to allocate buffer [ 25.853767@0] fb: malloc_osd_memory: size=1800000, FAILED. [ 25.857654@0] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 25.857666@0] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 25.857669@0] fb: use ion buffer for fb memory, fb_index=0 [ 25.857683@0] ion_dev ion_dev: Fail to allocate buffer [ 25.857687@0] fb: malloc_osd_memory: size=1800000, FAILED. [ 28.873014@3] the demux clock on, ref cnt: 1 [ 28.873024@3] the parser_top clock on, ref cnt: 1 [ 28.873028@3] the vdec clock on, ref cnt: 1 [ 28.873050@3] the clk_vdec_mux clock on, ref cnt: 1 [ 28.873062@3] vdec mux clock is 500000000 Hz [ 28.873126@3] vdec_create instance ffffff800c25d000, total 1 [ 28.873143@3] vdec_disable_DMC input->target= 0x0 [ 28.873146@3] vdec_release instance ffffff800c25d000, total 1 [ 28.873172@3] the clk_vdec_mux clock off, ref cnt: 0 [ 28.873176@3] the vdec clock off, ref cnt: 0 [ 28.873179@3] the parser_top clock off, ref cnt: 0 [ 28.873182@3] the demux clock off, ref cnt: 0 [ 29.022255@0] snd_spdif_dai: enterd aml_spdif_play,set_clock:5,sample_rate=4 [ 29.022279@0] snd_spdif_dai: set 958 audio clk div 2 [ 29.022292@0] hdmitx: hw: set audio [ 29.022296@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 29.022324@0] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 29.022327@0] hdmitx: hw: aud_n_para = 5824 [ 29.022344@0] hdmitx: hw: set channel status [ 29.022396@0] hdmitx: audio: Audio Type: PCM [ 29.022398@0] hdmitx: audio: set audio param [ 29.053591@1] audio_dsp: buf=0 [ 29.053602@1] audio_dsp: IEC958_mode_raw=0 [ 29.053647@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 29.053649@1] audio_dsp: last mode 0,now 0 [ 29.059474@1] snd_spdif_dai: set normal 512 fs /4 fs [ 29.059484@1] snd_spdif_dai: set 958 audio clk div 4 [ 29.059498@1] hdmitx: hw: set audio [ 29.059501@1] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 29.059529@1] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 29.059532@1] hdmitx: hw: aud_n_para = 8918 [ 29.059549@1] hdmitx: hw: set channel status [ 29.059601@1] hdmitx: audio: Audio Type: PCM [ 29.059603@1] hdmitx: audio: set audio param [ 29.059856@1] snd_spdif_dai: set normal 512 fs /4 fs [ 29.108621@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 29.108632@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 29.108635@3] fb: use ion buffer for fb memory, fb_index=0 [ 29.108649@3] ion_dev ion_dev: Fail to allocate buffer [ 29.108653@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 29.112639@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 29.112650@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 29.112653@3] fb: use ion buffer for fb memory, fb_index=0 [ 29.112668@3] ion_dev ion_dev: Fail to allocate buffer [ 29.112672@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 32.131379@3] the demux clock on, ref cnt: 1 [ 32.131390@3] the parser_top clock on, ref cnt: 1 [ 32.131393@3] the vdec clock on, ref cnt: 1 [ 32.131416@3] the clk_vdec_mux clock on, ref cnt: 1 [ 32.131427@3] vdec mux clock is 500000000 Hz [ 32.131490@3] vdec_create instance ffffff800c27a000, total 1 [ 32.131507@3] vdec_disable_DMC input->target= 0x0 [ 32.131510@3] vdec_release instance ffffff800c27a000, total 1 [ 32.131536@3] the clk_vdec_mux clock off, ref cnt: 0 [ 32.131539@3] the vdec clock off, ref cnt: 0 [ 32.131543@3] the parser_top clock off, ref cnt: 0 [ 32.131545@3] the demux clock off, ref cnt: 0 [ 32.280662@0] snd_spdif_dai: enterd aml_spdif_play,set_clock:5,sample_rate=4 [ 32.280686@0] snd_spdif_dai: set 958 audio clk div 2 [ 32.280700@0] hdmitx: hw: set audio [ 32.280704@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 32.280732@0] hdmitx: fs = 3, cd = 4, tmds_clk = 148352 [ 32.280735@0] hdmitx: hw: aud_n_para = 5824 [ 32.280751@0] hdmitx: hw: set channel status [ 32.280804@0] hdmitx: audio: Audio Type: PCM [ 32.280806@0] hdmitx: audio: set audio param [ 32.311838@0] audio_dsp: buf=0 [ 32.311848@0] audio_dsp: IEC958_mode_raw=0 [ 32.311896@0] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM [ 32.311898@0] audio_dsp: last mode 0,now 0 [ 32.317546@0] snd_spdif_dai: set normal 512 fs /4 fs [ 32.317557@0] snd_spdif_dai: set 958 audio clk div 4 [ 32.317570@0] hdmitx: hw: set audio [ 32.317573@0] hdmitx: hw: hdmitx tx_aud_src = 0, audio_param->channel_num = 1, hdev->aud_output_ch = 0 [ 32.317602@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148352 [ 32.317605@0] hdmitx: hw: aud_n_para = 8918 [ 32.317621@0] hdmitx: hw: set channel status [ 32.317673@0] hdmitx: audio: Audio Type: PCM [ 32.317676@0] hdmitx: audio: set audio param [ 32.317960@2] snd_spdif_dai: set normal 512 fs /4 fs [ 32.366927@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 32.366938@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 32.366940@3] fb: use ion buffer for fb memory, fb_index=0 [ 32.366955@3] ion_dev ion_dev: Fail to allocate buffer [ 32.366959@3] fb: malloc_osd_memory: size=1800000, FAILED. [ 32.370450@3] fb: malloc_osd_memory, cma:ffffff800ad14950 [ 32.370461@3] fb: malloc_osd_memory, 1218, base:0x000000003c800000, size:8388608 [ 32.370464@3] fb: use ion buffer for fb memory, fb_index=0 [ 32.370479@3] ion_dev ion_dev: Fail to allocate buffer [ 32.370483@3] fb: malloc_osd_memory: size=1800000, FAILED.