GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0; TE: 168455 BL2 Built : 20:32:17, Sep 8 2017. gxl g6296b83 - xiaobo.gu@droid12 set vdd cpu_a to 1120 mv set vdd cpu_b to 1050 mv set vddee to 1000 mv Board ID = 3 CPU clk: 1200MHz DQS-corr enabled DDR scramble enabled STICKY_REG0: 0x00000000 STICKY_REG1: 0x00000000 STICKY_REG9: 0x00000000 DDR3 chl: Rank0+1 @ 912MHz - PASS Rank0: 1024MB(auto)-2T-13 Rank1: 1024MB(auto)-2T-13 DataBus test pass! AddrBus test pass! -s Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600 Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x00065800 NOTICE: BL3-1: v1.0(release):a625749 NOTICE: BL3-1: Built : 11:25:15, Aug 25 2017 NOTICE: BL31: BL33 decompress pass mpu_config_enable:ok [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07] OPS=0x82 wdt: reset registers! 82 27 bc 2f a0 c0 dd 51 7c fd 30 90 [0.401551 Inits done] secure task start! high task start! low task start! ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g84dda8c (Feb 09 2018 - 11:03:10) DRAM: 2 GiB Relocation Offset is: 76eb4000 register usb cfg[0][1] = 0000000077f5b100 [CANVAS]canvas init boot_device_flag : 1 set wlan gpio pin 6. set bluetooth gpio pin 17. Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc. init bus_cycle=6, bus_timing=7, system=5.0ns reset failed get_chip_type and ret:fffffffe get_chip_type and ret:fffffffe chip detect failed and ret:fffffffe nandphy_init failed and ret=0xfffffff1 MMC: aml_priv->desc_buf = 0x0000000073eb4790 aml_priv->desc_buf = 0x0000000073eb6ab0 SDIO Port B: 0, SDIO Port C: 1 emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 init_part() 293: PART_TYPE_AML [mmc_init] mmc init success dtb magic 5f4c4d41 Amlogic multi-dtb tool Multi dtb detected Multi dtb tool version: v2 . Support 3 dtbs. aml_dt soc: gxm platform: q201 variant: 2g dtb 0 soc: gxm plat: q201 vari: 1g dtb 1 soc: gxm plat: q201 vari: 2g dtb 2 soc: gxm plat: q201 vari: 3g Find match dtb: 1 start dts,buffer=0000000073eb9300,dt_addr=0000000073ec4b00 Amlogic multi-dtb tool Multi dtb detected Multi dtb tool version: v2 . Support 3 dtbs. aml_dt soc: gxm platform: q201 variant: 2g dtb 0 soc: gxm plat: q201 vari: 1g dtb 1 soc: gxm plat: q201 vari: 2g dtb 2 soc: gxm plat: q201 vari: 3g Find match dtb: 1 parts: 10 00: logo 0000000002000000 1 01: recovery 0000000002000000 1 02: rsv 0000000000800000 1 03: tee 0000000000800000 1 04: crypt 0000000002000000 1 05: misc 0000000002000000 1 06: boot 0000000002000000 1 07: system 0000000080000000 1 08: cache 0000000020000000 2 09: data ffffffffffffffff 4 init_part() 293: PART_TYPE_AML eMMC/TSD partition table have been checked OK! check pattern success mmc env offset: 0x27400000 In: serial Out: serial Err: serial reboot_mode=cold_boot [store]To run cmd[emmc dtb_read 0x1000000 0x40000] _verify_dtb_checksum()-917: calc 86f8054a, store 86f8054a _verify_dtb_checksum()-917: calc 86f8054a, store 86f8054a dtb_read()-1039: total valid 2 dtb_read()-1106: do nothing Amlogic multi-dtb tool Multi dtb detected Multi dtb tool version: v2 . Support 3 dtbs. aml_dt soc: gxm platform: q201 variant: 2g dtb 0 soc: gxm plat: q201 vari: 1g dtb 1 soc: gxm plat: q201 vari: 2g dtb 2 soc: gxm plat: q201 vari: 3g Find match dtb: 1 vpu: clk_level in dts: 7 vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300) vpu: vpu_clk_gate_init_off vpp: vpp_init hpd_state=1 [1080p60hz] is invalid for cvbs. set hdmitx VIC = 16 config HPLL = 2970000 HPLL: 0xc000027b config HPLL done j = 4 vid_clk_div = 1 hdmitx: set enc for VIC: 16 HDMITX-DWC addr=0x10004006 rd_data=0x40 Error: HDMITX-DWC exp_data=0xff mask=0x9f rx version is 1.4 or below div=10 hdmtix: set audio hdmitx phy setting done saradc - saradc sub-system Usage: saradc saradc open - open a SARADC channel saradc close - close the SARADC saradc getval - get the value in current channel saradc get_in_range - return 0 if current value in the range of current channel SARADC closed. vpp: vpp_pq_load pq val error !!! Net: dwmac.c9410000amlkey_init() enter! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 Start read misc partition datas! info->attemp_times = 0 info->active_slot = 0 info->slot_info[0].bootable = 1 info->slot_info[0].online = 1 info->slot_info[1].bootable = 0 info->slot_info[1].online = 0 info->attemp_times = 0 attemp_times = 0 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=2 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7f851000 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7f851000 [CANVAS]addr=0x7f851000 width=5760, height=2160 amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet gpio: pin GPIOAO_2 (gpio 102) value is 1 InUsbBurn noSof Hit Enter or space or Ctrl+C key to stop autoboot -- : 0 ee_gate_off ... ## Booting Android Image at 0x01080000 ... reloc_addr =73f39550 copy done Kernel command line: buildvariant=user load dtb from 0x1000000 ...... Amlogic multi-dtb tool Single dtb detected Uncompressing Kernel Image ... OK kernel loaded at 0x01080000, end = 0x02242460 Loading Ramdisk to 73d38000, end 73ea2052 ... OK Loading Device Tree to 000000001fff1000, end 000000001ffff05f ... OK fdt_instaboot: no instaboot image Starting kernel ... uboot time: 2818312 us [ 0.000000@0] Initializing cgroup subsys cpu [ 0.000000@0] Initializing cgroup subsys cpuacct [ 0.000000@0] Linux version 3.14.29-g8855433 (gwx@AZW) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Fri Feb 9 11:12:16 CST 2018 [ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4 [ 0.000000@0] no prop version_code [ 0.000000@0] bootconsole [earlycon0] enabled [ 0.000000@0] fdt Reserved memory table: [ 0.000000@0] linux,di: 0x000000007e200000 - 0x0000000080000000 (30 MiB) [ 0.000000@0] DI: DI reserved memory: created CMA memory pool at 0x000000007e200000, size 30 MiB [ 0.000000@0] linux,chunk-reserve: 0x000000007a200000 - 0x000000007e200000 (64 MiB) [ 0.000000@0] linux,ion-dev: 0x0000000076200000 - 0x000000007a200000 (64 MiB) [ 0.000000@0] linux,vdin1_cma: 0x0000000075000000 - 0x0000000076000000 (16 MiB) [ 0.000000@0] cma: Reserved 16 MiB at 75000000, total cma pages:4096 [ 0.000000@0] linux,ppmgr: 0x0000000076200000 - 0x0000000076200000 (0 MiB) [ 0.000000@0] linux,codec_mm_cma: 0x000000005ec00000 - 0x0000000073c00000 (336 MiB) [ 0.000000@0] cma: Reserved 336 MiB at 5ec00000, total cma pages:90112 [ 0.000000@0] linux,picdec: 0x0000000076200000 - 0x0000000076200000 (0 MiB) [ 0.000000@0] Reserved memory: incorrect alignment of CMA region [ 0.000000@0] linux,codec_mm_reserved: 0x000000005ab00000 - 0x000000005ec00000 (65 MiB) [ 0.000000@0] fdt Reserved memory total: 579 MiB [ 0.000000@0] cma: Reserved 8 MiB at 74800000, total cma pages:92160 [ 0.000000@0] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000@0] PERCPU: Embedded 12 pages/cpu @ffffffc07616c000 s19968 r8192 d20992 u49152 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 511749 [ 0.000000@0] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,1080p60hz maxcpus=8 vout=1080p60hz,enable hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= cvbsdrv=0 pq= androidboot.firstboot=1 jtag=apao androidboot.hardware=amlogic androidboot.slot_suffix=_a buildvariant=user [ 0.000000@0] logo: osd1 [ 0.000000@0] logo: loaded [ 0.000000@0] logo: 0x3d800000 [ 0.000000@0] logo: 1080p60hz [ 0.000000@0] vout_serve: 1080p60hz [ 0.000000@0] vout_serve: enable: 1 [ 0.000000@0] logo: get hdmimode: 1080p60hz [ 0.000000@0] logo: get cvbsmode: 576cvbs [ 0.000000@0] tv_vout: cvbs performance line = 0 [ 0.000000@0] [amvecm] pq string error !!! [ 0.000000@0] jtag: jtag select 2 [ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000@0] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000@0] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000@0] Memory: 1420732K/2092032K available (11302K kernel code, 1289K rwdata, 4268K rodata, 1319K init, 3790K bss, 671300K reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] vmalloc : 0xffffff8000000000 - 0xffffff8040000000 ( 1024 MB) [ 0.000000@0] vmemmap : 0xffffff8040010000 - 0xffffff8042c10000 ( 44 MB) [ 0.000000@0] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc080000000 ( 2048 MB) [ 0.000000@0] .init : 0xffffffc001fb6000 - 0xffffffc0020ffe00 ( 1320 kB) [ 0.000000@0] .text : 0xffffffc001080000 - 0xffffffc001fb58d4 ( 15575 kB) [ 0.000000@0] .data : 0xffffffc002100000 - 0xffffffc002242460 ( 1290 kB) [ 0.000000@0] PM: Registered nosave memory: [mem 0x01080000-0x01fb4fff] [ 0.000000@0] SLUB: HWalign=64, Order=0-1, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000@0] arch_multi_cluster:1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns [ 0.008247@0] meson_bc_timer: mclk->mux_reg =ffffff8000014990,mclk->reg =ffffff8000016994 [ 0.016834@0] Console: colour dummy device 80x25 [ 0.021095@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.031671@0] pid_max: default: 32768 minimum: 301 [ 0.036582@0] Security Framework initialized [ 0.040786@0] SELinux: Initializing. [ 0.044530@0] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.051367@0] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.065348@0] Initializing cgroup subsys debug [ 0.065385@0] Initializing cgroup subsys freezer [ 0.068899@0] ftrace: allocating 38893 entries in 152 pages [ 0.125006@0] /cpus/cpu@0: Missing clock-frequency property [ 0.125046@0] /cpus/cpu@1: Missing clock-frequency property [ 0.130628@0] /cpus/cpu@2: Missing clock-frequency property [ 0.136258@0] /cpus/cpu@3: Missing clock-frequency property [ 0.141830@0] /cpus/cpu@100: Missing clock-frequency property [ 0.147612@0] /cpus/cpu@101: Missing clock-frequency property [ 0.153380@0] /cpus/cpu@102: Missing clock-frequency property [ 0.159162@0] /cpus/cpu@103: Missing clock-frequency property [ 0.164930@0] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available [ 0.215238@0] Meson chip version = RevA (22:A - 82:0) [ 0.233652@1] CPU1: Booted secondary processor [ 0.253627@2] CPU2: Booted secondary processor [ 0.273631@3] CPU3: Booted secondary processor [ 0.293668@4] CPU4: Booted secondary processor [ 0.313668@5] CPU5: Booted secondary processor [ 0.333679@6] CPU6: Booted secondary processor [ 0.353711@7] CPU7: Booted secondary processor [ 0.353802@0] Brought up 8 CPUs [ 0.382621@0] SMP: Total of 8 processors activated. [ 0.396336@2] sched: registering cpufreq notifiers for scale-invariant loads [ 0.397860@2] instabooting: 0 [ 0.417033@2] cma: cma_init_reserved_areas, use_cma_first:1 [ 0.417137@2] pinctrl core: initialized pinctrl subsystem [ 0.423149@2] regulator-dummy: no parameters [ 0.427678@3] NET: Registered protocol family 16 [ 0.433645@2] ramoops: using module parameters [ 0.436471@2] console [pstore-1] enabled [ 0.439813@2] pstore: Registered ramoops as persistent store backend [ 0.446186@2] ramoops: attached 0x100000@0x7300000, ecc: 0/0 [ 0.452934@2] cpuidle: using governor menu [ 0.456270@3] aml_vdac_init: module init [ 0.460098@2] register canvas platform driver [ 0.464443@2] register rdma platform driver [ 0.470518@2] vdso: 2 pages (1 code, 1 data) at base ffffffc002108000 [ 0.475028@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.482362@2] DMA: preallocated 256 KiB pool for atomic allocations [ 0.489253@2] software IO TLB [mem 0x56c00000-0x57000000] (4MB) mapped at [ffffffc056c00000-ffffffc056ffffff] [ 0.498249@2] Serial: AMBA PL011 UART driver [ 0.503200@2] aml_i2c version: 20140813 [ 0.506652@3] i2c-core: driver [pmu4] using legacy resume method [ 0.512694@2] codec_mm:codec_mm_module_init [ 0.516724@3] media_configs_system_init [ 0.520658@3] aml_watch_point_probe, in [ 0.524840@2] meson_mpll_clk: register mpll_clk_out0 success done [ 0.530453@2] meson_mpll_clk: register mpll_clk_out1 success done [ 0.536588@2] meson_mpll_clk: register mpll_clk_out2 success done [ 0.542906@2] clk_sys: register PLL sys_pll success done [ 0.548052@2] gxl_clk: [ xtal ] ->clockrate: 24000000Hz [ 0.553374@2] gxl_clk: [ 32Khz ] ->clockrate: 32000Hz [ 0.558580@2] gxl_clk: [ clk81 ] ->clockrate: 166666666Hz [ 0.564048@2] gxl_clk: [ fixed_pll ] ->clockrate: 2000000000Hz [ 0.570004@2] gxl_clk: [ fclk_div2 ] ->clockrate: 1000000000Hz [ 0.575948@2] gxl_clk: [ fclk_div3 ] ->clockrate: 666666666Hz [ 0.581815@2] gxl_clk: [ fclk_div4 ] ->clockrate: 500000000Hz [ 0.587673@2] gxl_clk: [ fclk_div5 ] ->clockrate: 400000000Hz [ 0.593541@2] gxl_clk: [ fclk_div7 ] ->clockrate: 285714285Hz [ 0.599422@2] gxl_clk: clock initialization complete [ 0.604579@2] clkmsr: Gxl msr_clk_reg0=ffffff800003c75c,msr_clk_reg2=ffffff800003e764 [ 0.615062@2] aml_iomap: amlogic iomap probe done [ 0.617690@3] pinmux-gxl c1109880.pinmux: Init pinux probe! [ 0.623912@2] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver [ 0.629783@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc) [ 0.637314@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc) [ 0.645533@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc) [ 0.653409@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc) domain-0 init dvfs: 4 domain-1 init dvfs: 4 [ 0.674020@2] codec_mm has 2 memory regions [ 0.674084@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok [ 0.680710@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok [ 0.689300@2] codec_mm has 2 memory regions [ 0.693409@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_cma ok [ 0.701428@2] codec_mm codec_mm.19: assigned reserved memory node linux,codec_mm_reserved ok [ 0.712454@2] vpu: driver version: v04 [ 0.713695@2] vpu: load vpu_clk: 666667000Hz(7) [ 0.718341@3] vpu: vpu_probe OK [ 0.723160@3] tv_vout: tvout_probe [ 0.724802@3] tv_vout: chrdev devno 266338304 for disp [ 0.729948@3] vout_notify: vout_register_server [ 0.734498@3] tv_vout: register tv module server ok [ 0.739700@2] tv_vout: create cdev tv [ 0.743131@2] tv_vout: tvout_probe OK [ 0.747455@2] canvas_probe reg=00000000c8838000,size=400 [ 0.752119@2] canvas maped reg_base =ffffff800009a000 [ 0.761549@3] rdma_probe [ 1.150547@2] bio: create slab at 0 [ 1.151704@3] SCSI subsystem initialized [ 1.153744@2] usbcore: registered new interface driver usbfs [ 1.159011@3] usbcore: registered new interface driver hub [ 1.164568@2] usbcore: registered new device driver usb [ 1.170576@3] i2c-gpio i2c_gpio.40: using pins 172 (SDA) and 173 (SCL) [ 1.176533@2] Linux video capture interface: v2.00 [ 1.181830@2] pps_core: LinuxPPS API ver. 1 registered [ 1.186089@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.195609@2] PTP clock support registered [ 1.200286@2] hdmitx: system: Ver: 2014May6 [ 1.203953@2] hdmitx: amhdmitx_probe [ 1.207789@2] hdmitx: hdmi_init_chip_type: 0 [ 1.211710@2] hdmitx hpd irq = 89 [ 1.215783@2] hdmitx20: Mapped PHY: 0xc1100000 [ 1.219448@2] hdmitx20: Mapped PHY: 0xc8834400 [ 1.223895@2] hdmitx20: Mapped PHY: 0xd0100000 [ 1.228361@2] hdmitx20: Mapped PHY: 0xc8100000 [ 1.232878@2] hdmitx20: Mapped PHY: 0xc883c000 [ 1.237274@2] hdmitx20: Mapped PHY: 0xc1104400 [ 1.241736@2] hdmitx20: Mapped PHY: 0xc883a000 [ 1.246205@2] hdmitx20: Mapped PHY: 0xda83a000 [ 1.250662@2] hdmitx20: Mapped PHY: 0xd0044000 [ 1.255127@2] hdmitx: alread display in uboot 0x10 [ 1.260018@2] avmute set to 1 [ 1.262916@2] hdmitx: attr 444,8bit [ 1.266975@0] tv_vout: tv_set_current_vmode[925]fps_target_mode=19 [ 1.272629@0] tv_vout: mode is 19,sync_duration_den=1,sync_duration_num=60 [ 1.279556@0] hdmitx: system: irq 80000002 [ 1.283671@0] tv_vout: already display in uboot [ 1.288198@0] vout_serve: vinfo mode is: 1080p60hz [ 1.293017@0] vout_serve: init mode 1080p60hz [ 1.297643@3] vout_serve: create_vout_fops OK [ 1.301761@3] vout_serve: create vout attribute OK [ 1.306595@3] vout_serve: meson_vout_probe OK [ 1.311169@2] logo: logo_init [ 1.314378@2] osd_rdma: osd_rdma_init: rdma_table p=0x74841000,op=0x74841000 , v=0xffffff80000b9000 [ 1.323109@2] rdma_register, rdma_table_addr ffffff80000c9000 rdma_table_addr_phy 74842000 reg_buf ffffffc05699d000 [ 1.333549@2] rdma_register success, handle 1 table_size 4096 [ 1.339299@2] osd_rdma: osd_rdma_init:osd reset rdma handle = 1. [ 1.345377@2] rdma_register, rdma_table_addr ffffff80000d9000 rdma_table_addr_phy 74843000 reg_buf ffffffc0572d4000 [ 1.355842@2] rdma_register success, handle 2 table_size 4096 [ 1.361610@2] osd_rdma: osd_rdma_init:osd rdma handle = 2. [ 1.367650@3] Advanced Linux Sound Architecture Driver Initialized. [ 1.374107@3] Bluetooth: Core ver 2.18 [ 1.377330@2] NET: Registered protocol family 31 [ 1.381825@2] Bluetooth: HCI device and connection manager initialized [ 1.388405@2] Bluetooth: HCI socket layer initialized [ 1.393463@2] Bluetooth: L2CAP socket layer initialized [ 1.398744@2] Bluetooth: SCO socket layer initialized [ 1.403791@2] NetLabel: Initializing [ 1.407373@2] NetLabel: domain hash size = 128 [ 1.411928@2] NetLabel: protocols = UNLABELED CIPSOv4 [ 1.417131@2] NetLabel: unlabeled traffic allowed by default [ 1.425242@3] Switched to clocksource arch_sys_counter [ 1.469581@2] register gxtv_demod demod driver [ 1.470012@3] [amlatvdemod..]aml_atvdemod_init. [ 1.473107@3] NET: Registered protocol family 2 [ 1.478157@3] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.485134@3] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 1.492087@3] TCP: Hash tables configured (established 16384 bind 16384) [ 1.498749@3] TCP: reno registered [ 1.501978@3] UDP hash table entries: 1024 (order: 3, 32768 bytes) [ 1.508233@3] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes) [ 1.515105@3] NET: Registered protocol family 1 [ 1.519764@3] RPC: Registered named UNIX socket transport module. [ 1.525519@3] RPC: Registered udp transport module. [ 1.530406@3] RPC: Registered tcp transport module. [ 1.535338@3] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.542117@3] pwm: output_co = 16 ; clock_co = 8 [ 1.546631@3] pwm: npwm= 16 [ 1.549617@2] pwm: probe ok [ 1.552596@2] wifi: power_on_pin_OD = 0; [ 1.556163@2] aml_wifi wifi.35: [wifi_dev_probe] no power_on_pin2 [ 1.562288@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm phandle val=41;pwm-channel1=4;pwm-channel2=12 [ 1.572331@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config1[0] = 30541 [ 1.580027@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config2[0] = 30518 [ 1.587727@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config1[1] = 15270 [ 1.595427@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config2[1] = 15259 [ 1.603121@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config1[2] = 6 [ 1.605332@0] hdmitx: plugin [ 1.613365@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] pwm_config2[2] = 9 [ 1.620714@2] aml_wifi wifi.35: [pwm_double_channel_conf_dt] wifi pwm dt ok [ 1.627729@2] aml_wifi wifi.35: [pwm_double_channel_conf] wifi pwm conf ok [ 1.634661@2] aml_wifi wifi.35: [wifi_dev_probe] dhd_static_buf setup [ 1.641177@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated [ 1.648716@2] aml_wifi wifi.35: [wifi_dev_probe] interrupt_pin=241 [ 1.654921@2] aml_wifi wifi.35: [wifi_dev_probe] irq_num=100, irq_trigger_type=1 [ 1.662115@0] EDID Parser: [ 1.662471@0] hdmitx: edid: change preferred_mode from 0 to 31 [ 1.662474@0] hdmitx: get PMT vic: 16 [ 1.662477@0] hdmitx: edid: find IEEEOUT [ 1.662484@0] hdmitx: update rx hdr info 0 at edid parsing [ 1.662527@0] 00ffffffffffff004dd9039d0101010101190103805f36780a0dc9a057479827 [ 1.662527@0] 12484c2108008180a9c0714fb3000101010101010101023a801871382d40582c [ 1.662527@0] 4500b8173200001e011d007251d01e206e285500b8173200001e000000fc0053 [ 1.662527@0] 4f4e5920545620202a30300a000000fd00303e0e460f000a20202020202001b9 [ 1.662527@0] [ 1.662527@0] [ 1.662565@0] 02033ef0531f101405130420223c3e121603071115020601290d7f071507503d [ 1.662565@0] 07bc830f000074030c002000b82d2fd00a0140007f203070809076e200fb023a [ 1.662565@0] 80d072382d40102c4580b8173200001e011d00bc52d01e20b8285540b8173200 [ 1.662565@0] 001e011d80d0721c1620102c2580b8173200009e00000000000000000000008d [ 1.662565@0] [ 1.662565@0] [ 1.662575@0] hdmitx: video: get current mode: 1080p60hz [ 1.662577@0] hdmitx: update rx hdr info 0 [ 1.662579@0] hdmitx: update physcial size: 950 540 [ 1.662595@0] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16 [ 1.662607@0] hdmtix: set audio [ 1.662614@0] hdmitx tx_aud_src = 0 [ 1.662635@0] hdmitx: fs = 0, cd = 4, tmds_clk = 148500 [ 1.662637@0] hdmitx aud_n_para = 6144 [ 1.785570@2] aml_wifi wifi.35: [wifi_dev_probe] power_on_pin=240 [ 1.791683@2] aml_wifi wifi.35: [wifi_dev_probe] clock_32k_pin=0 [ 1.798008@2] aml_wifi wifi.35: [wifi_setup_dt] wifi_setup_dt [ 1.803531@2] aml_wifi wifi.35: [wifi_setup_dt] interrupt_pin(241) [ 1.809730@2] aml_wifi wifi.35: [wifi_setup_dt] power_on_pin(240) [ 1.816217@2] Unpacking initramfs... [ 1.877444@3] Freeing initrd memory: 1448K (ffffffc073d38000 - ffffffc073ea2000) [ 1.884485@2] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 1.885863@2] Initialise system trusted keyring [ 1.890363@2] audit: initializing netlink subsys (disabled) [ 1.896007@2] audit: type=2000 audit(1.820:1): initialized [ 1.902379@3] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.915599@2] VFS: Disk quotas dquot_6.5.2 [ 1.915908@2] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.926070@2] NFS: Registering the id_resolver key type [ 1.926141@2] Key type id_resolver registered [ 1.930404@2] Key type id_legacy registered [ 1.934611@2] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.941645@2] NTFS driver 2.1.30 [Flags: R/W]. [ 1.946442@3] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.954055@3] fuse init (API version 7.22) [ 1.958386@3] msgmni has been set to 3497 [ 1.962959@2] NET: Registered protocol family 38 [ 1.966163@2] Key type asymmetric registered [ 1.970306@2] Asymmetric key parser 'x509' registered [ 1.975792@3] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.982997@3] io scheduler noop registered [ 1.987114@3] io scheduler deadline registered [ 1.991805@2] io scheduler cfq registered (default) [ 2.047307@0] meson-rng c8834000.rng: hwrng registered [ 2.050998@0] loop: module loaded [ 2.051665@0] zram: Created 1 device(s) ... [ 2.055474@0] mtdoops: mtd device (mtddev=name/number) must be supplied [ 2.061883@0] tun: Universal TUN/TAP device driver, 1.6 [ 2.066338@0] tun: (C) 1999-2004 Max Krasnyansky [ 2.198570@0] libphy: stmmac: probed [ 2.198604@0] eth0: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active [ 2.203143@0] eth0: PHY ID 001cc916 at 7 IRQ POLL (stmmac-0:07) [ 2.209658@1] PPP generic driver version 2.4.2 [ 2.213772@1] PPP BSD Compression module registered [ 2.218474@1] PPP Deflate Compression module registered [ 2.223722@1] PPP MPPE Compression module registered [ 2.228701@1] NET: Registered protocol family 24 [ 2.233519@0] usbcore: registered new interface driver asix [ 2.239132@0] usbcore: registered new interface driver ax88179_178a [ 2.245438@1] usbcore: registered new interface driver cdc_ether [ 2.251389@0] usbcore: registered new interface driver net1080 [ 2.257303@0] usbcore: registered new interface driver cdc_subset [ 2.263412@1] usbcore: registered new interface driver zaurus [ 2.269231@0] usbcore: registered new interface driver cdc_ncm [ 2.275264@1] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.281632@1] ehci-h20ahb: H20AHB-EHCI Host Controller driver [ 2.287707@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.294264@1] usbcore: registered new interface driver cdc_acm [ 2.299699@1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.308064@0] usbcore: registered new interface driver usb-storage [ 2.314375@1] usbcore: registered new interface driver usbserial [ 2.320946@1] amlogic-new-usb2 d0078000.usb2phy: USB2 phy probe:phy_mem:0xd0078000, iomap phy_base:0xffffff800010e000 [ 2.331127@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port [ 2.337676@0] amlogic-new-usb3 d0078080.usb3phy: USB3 phy probe:phy_mem:0xd0078080, iomap phy_base:0xffffff800011a080 [ 2.349071@0] mousedev: PS/2 mouse device common for all mice [ 2.354795@1] i2c /dev entries driver [ 2.358378@0] IR NEC protocol handler initialized [ 2.362482@0] IR RC5(x) protocol handler initialized [ 2.367501@0] IR RC6 protocol handler initialized [ 2.372191@0] IR JVC protocol handler initialized [ 2.376959@0] IR Sony protocol handler initialized [ 2.381729@0] IR RC5 (streamzap) protocol handler initialized [ 2.387521@0] IR SANYO protocol handler initialized [ 2.392422@0] IR MCE Keyboard/mouse protocol handler initialized [ 2.398641@1] usbcore: registered new interface driver uvcvideo [ 2.404392@1] USB Video Class driver (1.1.1) [ 2.408869@0] usbcore: registered new interface driver cx231xx [ 2.414544@0] cx231xx: Cx231xx dvb Extension initialized [ 2.420896@0] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com [ 2.428766@0] Bluetooth: HCI UART driver ver 2.2 [ 2.433182@0] Bluetooth: HCI H4 protocol initialized [ 2.438550@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 2.445951@0] cpu cpu4: bL_cpufreq_init: CPU 4 initialized [ 2.449350@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 2.457215@1] CPUidle arm64: cpuidle init start!! [ 2.462171@1] CPUidle arm64: cpuidle init done! [ 2.466872@0] hidraw: raw HID events driver (C) Jiri Kosina [ 2.475551@0] @@@@@@@@@@_____2______in dia_init() [ 2.476494@0] ATVR driver - init called! [ 2.484149@1] usbcore: registered new interface driver usbhid [ 2.486229@1] usbhid: USB HID core driver [ 2.490857@0] ashmem: initialized [ 2.494098@0] logger: created 256K log 'log_main' [ 2.498828@0] logger: created 256K log 'log_events' [ 2.503645@0] logger: created 256K log 'log_radio' [ 2.508498@0] logger: created 256K log 'log_system' [ 2.517286@0] meson_uart c81004c0.serial: ==uart0 reg addr = ffffff800011c4c0 [ 2.520096@0] c81004c0.serial: ttyS0 at MMIO 0xc81004c0 (irq = 225, base_baud = 1500000) is a meson_uart [ 2.535121@0] meson_uart c81004c0.serial: ttyS0 use xtal(8M) 24000000 change 0 to 115200 [ 2.537767@0] console [ttyS0] enabled [ 2.537767@0] console [ttyS0] enabled [ 2.545009@0] bootconsole [earlycon0] disabled [ 2.545009@0] bootconsole [earlycon0] disabled [ 2.554449@0] meson_uart c11084c0.serial: ==uart1 reg addr = ffffff800011e4c0 [ 2.560921@0] c11084c0.serial: ttyS1 at MMIO 0xc11084c0 (irq = 58, base_baud = 1500000) is a meson_uart [ 2.571169@0] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff] [ 2.580093@0] meson-gpu-clkgen: probe of c883c000.gpu_clk failed with error -16 [ 2.587754@0] hdmitx_hdcp_init [ 2.591465@0] aml_vrtc rtc.34: rtc core: registered aml_vrtc as rtc0 [ 2.597086@0] BLASTER Driver Init [ 2.601136@0] secmon has 1 memory regions [ 2.603851@0] secmon: share in base: 0xffffff800013a000, share out base: 0xffffff800013c000 [ 2.612150@0] secmon secmon.4: assigned reserved memory node linux,secmon ok [ 2.619092@0] secmon: probe done [ 2.622968@0] storage: storage in base: 0xffffff8001800000 [ 2.627761@0] storage: storage out base: 0xffffff8001880000 [ 2.633220@0] storage: storage block base: 0xffffff8001900000 [ 2.638961@0] storage: probe done! [ 2.643607@1] aml_sd_emmc_probe: line 3608 [ 2.646377@1] mmc driver version: 1.07, 2017-4-26: Support new emmc host controller for version 3 [ 2.655809@1] aml_sd_emmc_reg_init 1152 [ 2.658990@1] get property: ocr_avail, value:0x00200080 [ 2.665428@1] get property: f_min, value:300000 [ 2.671516@1] get property: f_max, value:100000000 [ 2.677906@1] get property: max_req_size, value:0x00020000 [ 2.684371@1] get property: pinname, str:emmc [ 2.690163@1] get property: card_type, value:1 [ 2.695861@1] get property: gpio_dat3, str: [ 2.701273@1] get property: hw_reset, str: [ 2.706750@1] emmc:pdata->caps = c0000d47 [ 2.710679@1] emmc:pdata->caps2 = 18060 [ 2.714468@1] emmc:pdata->pm_caps = 0 [ 2.718123@1] storage 1, boot 1 [ 2.721196@1] get_storage_dev return 1 [ 2.765285@1] [aml_sd_emmc_probe] aml_sd_emmc_probe() success! [ 2.765512@1] aml_sd_emmc_probe: line 3608 [ 2.769938@1] aml_sd_emmc_reg_init 1152 [ 2.773400@1] get property: ocr_avail, value:0x00200080 [ 2.779835@1] get property: f_min, value:400000 [ 2.785927@1] get property: f_max, value:100000000 [ 2.792327@1] get property: max_req_size, value:0x00020000 [ 2.798821@1] get property: irq_in, value:3 [ 2.804464@1] get property: irq_out, value:5 [ 2.810205@1] get property: gpio_cd, str: [ 2.815608@1] get property: pinname, str:sd [ 2.821196@1] get property: jtag_pin, str: [ 2.826663@1] get property: card_type, value:5 [ 2.832328@1] get property: gpio_dat3, str: [ 2.837783@1] sd:pdata->caps = 7 [ 2.840947@1] sd:pdata->caps2 = 0 [ 2.844225@1] sd:pdata->pm_caps = 0 [ 123.486625@2] random: nonblocking pool is initialized