ive the problem that since CoreELEC-S912.arm-9.0-nightly_20190124 my H96Pro+ S912 need double time to boot up! normal it need to 20190120 35sec. now over 60sec…
ive found some errors in log 02_System.log
if found out that this only appears when booting from internal emmc!
ive using errorfree internal flash since month…
build 20190120 -
[ 18.285329@0] hdmitx: system: PHY Setting Done
[ 18.285347@0] hdmitx: system: irq 80000001
[ 18.289348@0] Sink is HDMI device
[ 18.289361@0] hdmitx: system: packet: can't get vendor data
[ 18.289366@0] hdmitx: video: vinfo: 1080p50hz 50 1
[ 18.289374@0] hdmitx: video: vinfo recalc: 1080p50hz 50 1
[ 18.289381@0] hdmtix: set audio
[ 18.289393@0] hdmitx tx_aud_src = 0
[ 18.289425@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148500
[ 18.289430@0] hdmitx aud_n_para = 6272
[ 18.289452@0] hdmitx set channel status
[ 18.289518@0] hdmitx: audio: Audio Type: PCM
[ 18.289528@0] hdmitx: video: VIC: 31 (31) 1920x1080p50hz
[ 18.289540@0] hdmitx: video: Bit depth: 8-bit, Colour range RGB: limited, YCC: limited, Colourspace: YUV444
[ 18.289548@0] hdmitx: video: Colorimetry: bt709
[ 18.289555@0] hdmitx: video: PLL clock: 0xc000027b, Vid clock div 0x000a339c
[ 18.289568@0] Start = 0x10000100 End = 0x100001ff
[ 18.289581@0] [0x10000104]: 0x00000001
[ 18.289778@0] [0x10000180]: 0x000000ff
[ 18.289784@0] [0x10000181]: 0x000000ff
[ 18.289790@0] [0x10000182]: 0x00000003
[ 18.289796@0] [0x10000183]: 0x00000007
[ 18.289802@0] [0x10000184]: 0x0000003f
[ 18.289808@0] [0x10000185]: 0x00000002
[ 18.289816@0] [0x10000187]: 0x000000ff
[ 18.289822@0] [0x10000188]: 0x00000003
[ 18.290017@0] fb: osd current vmode=1080p50hz, cmd: 0x10000
[ 18.306470@4] fb: osd[0] canvas.idx =0x40
[ 18.306472@4] fb: osd[0] canvas.addr=0xb9300000
[ 18.306474@4] fb: osd[0] canvas.width=7680
[ 18.306476@4] fb: osd[0] canvas.height=2160
[ 18.306478@4] fb: osd[0] frame.width=1920
[ 18.306480@4] fb: osd[0] frame.height=1080
[ 18.366636@4] fb: osd[0] canvas.idx =0x40
[ 18.366639@4] fb: osd[0] canvas.addr=0xb9300000
[ 18.366641@4] fb: osd[0] canvas.width=7680
[ 18.366643@4] fb: osd[0] canvas.height=3240
[ 18.366645@4] fb: osd[0] frame.width=1920
[ 18.366647@4] fb: osd[0] frame.height=1080
[ 21.357630@6] audio_dsp: buf=0
[ 21.357649@6] audio_dsp: IEC958_mode_raw=0
[ 21.357700@6] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 21.357705@6] audio_dsp: last mode 0,now 0
[ 21.370889@6] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 21.370906@6] aml_spdif_dai: share the same clock
[ 21.370919@6] aml_audio_hw: IEC958 PCM32
[ 21.370927@6] hdmitx: audio: aout notify rate 44100
[ 21.370931@6] hdmitx: audio: aout notify size 32
[ 21.370937@6] hdmitx: audio: no update
[ 21.370950@6] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 21.371367@6] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 21.371381@6] aml_spdif_dai: share the same clock
[ 21.371394@6] aml_audio_hw: IEC958 PCM32
[ 21.371402@6] hdmitx: audio: aout notify rate 44100
[ 21.371407@6] hdmitx: audio: aout notify size 32
[ 21.371412@6] hdmitx: audio: no update
[ 21.371425@6] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 21.371700@6] channel count should be 8, we got 2 aborting
################################################################################
… output of lsmod
LibreELEC release: S912.arm-nightly_20190120
################################################################################
Module Size Used by
hci_uart 30134 1
bluetooth 340354 2 hci_uart
since 201901024 -Log is from 201901029
[ 20.186789@1] Bluetooth: HCI device and connection manager initialized
[ 20.186825@1] Bluetooth: HCI socket layer initialized
[ 20.186836@1] Bluetooth: L2CAP socket layer initialized
[ 20.186874@1] Bluetooth: SCO socket layer initialized
[ 20.195249@1] Bluetooth: HCI UART driver ver 2.2
[ 20.195265@1] Bluetooth: HCI H4 protocol initialized
[ 20.195270@1] Bluetooth: HCI BCSP protocol initialized
[ 20.195275@1] Bluetooth: HCILL protocol initialized
[ 20.195279@1] Bluetooth: HCIATH3K protocol initialized
[ 20.195284@1] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[ 24.086194@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 24.086210@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 24.086218@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 24.086242@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 24.086403@6] [aml_sd_emmc_data_thread] retry cmd 18 the 8-th time(s)
[ 24.086410@6] emmc, 8 retry, adj 6 -> 7
[ 24.086428@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 24.086458@6] aml_sd_emmc_data_thread : 2586
[ 28.181194@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 28.181210@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 28.181218@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 28.181242@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 28.181402@6] [aml_sd_emmc_data_thread] retry cmd 18 the 7-th time(s)
[ 28.181408@6] emmc, 7 retry, adj 7 -> 8
[ 28.181425@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 28.181456@6] aml_sd_emmc_data_thread : 2586
[ 32.276190@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 32.276200@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 32.276207@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 32.276232@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 32.276390@6] [aml_sd_emmc_data_thread] retry cmd 18 the 6-th time(s)
[ 32.276396@6] emmc, 6 retry, adj 8 -> 9
[ 32.276413@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 32.276443@6] aml_sd_emmc_data_thread : 2586
[ 36.371191@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 36.371202@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 36.371210@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 36.371235@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 36.371388@6] [aml_sd_emmc_data_thread] retry cmd 18 the 5-th time(s)
[ 36.371394@6] emmc, 5 retry, adj 9 -> 0
[ 36.371411@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 36.371433@6] aml_sd_emmc_data_thread : 2586
[ 40.466191@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 40.466201@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 40.466209@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 40.466233@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 40.466390@6] [aml_sd_emmc_data_thread] retry cmd 18 the 4-th time(s)
[ 40.466396@6] emmc, 4 retry, adj 0 -> 1
[ 40.466413@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 40.466442@6] aml_sd_emmc_data_thread : 2586
[ 44.561191@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 44.561202@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 44.561209@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 44.561233@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 44.561393@6] [aml_sd_emmc_data_thread] retry cmd 18 the 3-th time(s)
[ 44.561399@6] emmc, 3 retry, adj 1 -> 2
[ 44.561417@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 44.561445@6] aml_sd_emmc_data_thread : 2586
[ 48.656191@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 48.656203@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 48.656210@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 48.656238@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 48.656391@6] [aml_sd_emmc_data_thread] retry cmd 18 the 2-th time(s)
[ 48.656397@6] emmc, 2 retry, adj 2 -> 3
[ 48.656414@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 48.656444@6] aml_sd_emmc_data_thread : 2586
[ 52.751191@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 52.751203@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 52.751211@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 52.751239@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 52.751396@6] [aml_sd_emmc_data_thread] retry cmd 18 the 1-th time(s)
[ 52.751403@6] emmc, 1 retry, adj 3 -> 4
[ 52.751420@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 52.751445@6] aml_sd_emmc_data_thread : 2586
[ 56.846190@0] [aml_sd_emmc_irq] emmc: desc_timeout,vstat:0xe1ff1000,virqc:3fff
[ 56.846202@0] [aml_host_bus_fsm_show] emmc: err: wait for irq service, bus_fsm:0x8
[ 56.846209@0] [mmc_cmd_LBA_show] emmc: cmd 18, arg 0x14000, operation is in [reserved] disk!
[ 56.846236@6] aml_sd_emmc_data_thread 2639 emmc: cmd:18
[ 56.846390@6] [aml_sd_emmc_data_thread] Command retried failed line:2752, cmd:18
[ 56.846407@0] [aml_sd_emmc_irq] emmc: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 56.846433@6] aml_sd_emmc_data_thread : 2586
[ 56.846465@4] _dtb_read: save dtb error
[ 56.846465@2] mmc_dtb_read: read failed:-14
[ 57.360752@2] 8021q: 802.1Q VLAN Support v1.8
[ 60.386727@1] codec:vdec_create instance ffffff800483a000, total 1
[ 61.324028@7] libphy: stmmac-0:00 - Link is Up - 1000/Full
[ 61.324059@7] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 63.747678@1] audio_dsp: buf=0
[ 63.747695@1] audio_dsp: IEC958_mode_raw=0
[ 63.747728@1] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 63.747732@1] audio_dsp: last mode 0,now 0
[ 63.753209@1] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 63.753274@1] aml_spdif_dai: share the same clock
[ 63.753284@1] aml_audio_hw: IEC958 PCM32
[ 63.753290@1] hdmitx: audio: aout notify rate 44100
[ 63.753294@1] hdmitx: audio: aout notify size 32
[ 63.753299@1] hdmitx: audio: aout notify format CT_PCM
[ 63.753304@1] hdmtix: set audio
[ 63.753318@1] hdmitx tx_aud_src = 0
[ 63.753346@1] hdmitx: fs = 2, cd = 4, tmds_clk = 148500
[ 63.753350@1] hdmitx aud_n_para = 6272
[ 63.753369@1] hdmitx set channel status
[ 63.753427@1] hdmitx: audio: Audio Type: PCM
[ 63.753430@1] hdmitx: audio: set audio param
[ 63.753441@1] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 63.753924@1] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 63.753932@1] aml_spdif_dai: share the same clock
[ 63.753941@1] aml_audio_hw: IEC958 PCM32
[ 63.753947@1] hdmitx: audio: aout notify rate 44100
[ 63.753951@1] hdmitx: audio: aout notify size 32
[ 63.753954@1] hdmitx: audio: no update
[ 63.753962@1] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 63.754157@1] channel count should be 8, we got 2 aborting
[ 63.994215@0] hdmitx: set frac_rate_policy as 0
[ 63.994245@0] vout_serve: vmode set to 1080p50hz
[ 63.994272@0] hdmitx: video: vinfo: 1080p60hz 60 1
[ 63.994279@0] hdmitx: video: vinfo recalc: 1080p60hz 60 1
[ 63.994283@0] fb: osd current vmode=1080p60hz, cmd: 0x50000
[ 63.994292@0] tv_vout: tv_set_current_vmode[919]fps_target_mode=18
[ 63.994298@0] tv_vout: mode is 18,sync_duration_den=1,sync_duration_num=50
[ 63.994311@0] tv_vout: TV mode 1080p50hz selected.
[ 63.994318@0]
[ 63.994318@0] vdac_enable: on:0,module_sel:8
[ 63.994328@0]
[ 63.994328@0] vdac_enable: on:0,module_sel:8
[ 63.994337@0] tv_vout: new mode =1080p50hz set ok
[ 63.994341@0] vout_serve: vinfo mode is: 1080p50hz
[ 63.994344@0] vout_serve: new mode 1080p50hz set ok
[ 63.994361@0] hdmitx: video: auto - get current mode: 1080p50hz
[ 63.994366@0] hdmitx: stream colourdepth was 8 in para 0x01b46430 (1920x1080p60hz)
[ 63.994371@0] hdmitx: update rx hdr info 5
[ 63.994374@0] hdmitx: update physcial size: 1600 900
[ 63.994390@0] hdmitx: hdev->para now = para at 0x01b46330
[ 63.994395@0] hdmitx: Stream colourdepth is 8 in para 0x01b46330 (1920x1080p50hz - VIC: 31)
[ 63.994434@0] hdmitx: system: already init VIC = 0 Now VIC = 31
[ 63.994439@0] hdmitx: system: params found at 0x01b44310
[ 63.994442@0] hdmitx: system: cur_param = param at 0x01b44310 colourdepth 8
[ 63.994449@0] hdmitx: video: pixel freq 148500, tmds clock 148500, MaxClock1 300000, HF_IEEEOUI 0xc45dd8, MaxClock2 600000
[ 63.994454@0] hdmitx: rx has SCDC present indicator
[ 63.996468@0] hdmirx version is 2.0
[ 63.996472@0] hdmitx div40: 0
[ 64.023746@0] hdmitx: system: set pll
[ 64.023752@0] hdmitx: system: param->VIC:31
[ 64.023757@0] hdmitx: set clk: VIC = 31 cd = 4 frac_rate = 0
[ 64.023768@0] hdmitx: 1920x1080p50hz doesn't have frac_rate
[ 64.023774@0] config HPLL = 2970000
[ 64.023797@0] HPLL: 0xc000027b
[ 64.023800@0] config HPLL done
[ 64.023809@0] set_hpll_od3_clk_div[442] div = 6
[ 64.023817@0] j = 4 vid_clk_div = 1
[ 64.023828@0] hdmitx: set enc for VIC: 31
[ 64.023868@0] hdmitx_set_hw[4896] set VIC = 31
[ 64.023875@0] hdmitx: system: irq 80000001
[ 64.023933@0] Set rgb_ycc to 2
[ 64.024067@0] hdmitx: system: irq 80000001
[ 64.039895@0] Start = 0x10000100 End = 0x100001ff
[ 64.039906@0] [0x10000104]: 0x00000001
[ 64.040075@0] [0x10000180]: 0x000000ff
[ 64.040080@0] [0x10000181]: 0x000000ff
[ 64.040084@0] [0x10000182]: 0x00000003
[ 64.040089@0] [0x10000183]: 0x00000007
[ 64.040093@0] [0x10000184]: 0x0000003f
[ 64.040097@0] [0x10000185]: 0x00000002
[ 64.040103@0] [0x10000187]: 0x000000ff
[ 64.040108@0] [0x10000188]: 0x00000003
[ 64.155755@0] hdmitx: system: PHY Setting Done
[ 64.159779@0] Sink is HDMI device
[ 64.159792@0] hdmitx: system: packet: can't get vendor data
[ 64.159798@0] hdmitx: video: vinfo: 1080p50hz 50 1
[ 64.159805@0] hdmitx: video: vinfo recalc: 1080p50hz 50 1
[ 64.159811@0] hdmtix: set audio
[ 64.159823@0] hdmitx tx_aud_src = 0
[ 64.159854@0] hdmitx: fs = 2, cd = 4, tmds_clk = 148500
[ 64.159860@0] hdmitx aud_n_para = 6272
[ 64.159881@0] hdmitx set channel status
[ 64.159949@0] hdmitx: audio: Audio Type: PCM
[ 64.159959@0] hdmitx: video: VIC: 31 (31) 1920x1080p50hz
[ 64.159971@0] hdmitx: video: Bit depth: 8-bit, Colour range RGB: limited, YCC: limited, Colourspace: YUV444
[ 64.159980@0] hdmitx: video: Colorimetry: bt709
[ 64.159987@0] hdmitx: video: PLL clock: 0xc000027b, Vid clock div 0x000a339c
[ 64.159994@0] fb: osd current vmode=1080p50hz, cmd: 0x10000
[ 64.217198@7] fb: osd[0] canvas.idx =0x40
[ 64.217200@7] fb: osd[0] canvas.addr=0xb9300000
[ 64.217203@7] fb: osd[0] canvas.width=7680
[ 64.217205@7] fb: osd[0] canvas.height=3240
[ 64.217207@7] fb: osd[0] frame.width=1920
[ 64.217209@7] fb: osd[0] frame.height=1080
[ 64.622725@0] vout_serve: vmode set to null
[ 64.622763@0] vout_serve: disable HDMI PHY as soon as possible
[ 64.622770@0] hdmitx: video: vinfo: 1080p50hz 50 1
[ 64.622777@0] hdmitx: video: vinfo recalc: 1080p50hz 50 1
[ 64.622781@0] fb: osd current vmode=1080p50hz, cmd: 0x50000
[ 64.622789@0] tv_vout: tv_set_current_vmode[919]fps_target_mode=59
[ 64.622794@0] tv_vout: mode is 59,sync_duration_den=1,sync_duration_num=60
[ 64.622808@0] tv_vout: 3tvinfo 58 not find
[ 64.622811@0] tv_vout: new mode =null set ok
[ 64.622815@0] vout_serve: vinfo mode is: null
[ 64.622818@0] vout_serve: new mode null set ok
[ 64.622828@0] hdmitx: edid: not find mapped vic
[ 64.622836@0] hdmitx: video: auto - get current mode: null
[ 64.622841@0] hdmitx: stream colourdepth was 8 in para 0x01b46330 (1920x1080p50hz)
[ 64.622845@0] hdmitx: display colourdepth was 8 in cur_param 0x01b44310 (VIC: 31)
[ 64.622849@0] hdmitx: update physcial size: 1600 900
[ 64.622854@0] hdmitx: video: null not valid hdmi mode
[ 64.622882@0] fb: osd current vmode=null, cmd: 0x10000
[ 64.636909@0] hdmitx: set frac_rate_policy as 0
[ 64.636930@0] vout_serve: vmode set to 1080p50hz
[ 64.636945@0] vout_serve: disable HDMI PHY as soon as possible
[ 64.636950@0] hdmitx: video: vinfo: null 60 1
[ 64.636955@0] hdmitx: video: vinfo recalc: null 60 1
[ 64.636959@0] fb: osd current vmode=null, cmd: 0x50000
[ 64.636964@0] tv_vout: tv_set_current_vmode[919]fps_target_mode=18
[ 64.636968@0] tv_vout: mode is 18,sync_duration_den=1,sync_duration_num=50
[ 64.636979@0] tv_vout: TV mode 1080p50hz selected.
[ 64.636984@0]
[ 64.636984@0] vdac_enable: on:0,module_sel:8
[ 64.636994@0]
[ 64.636994@0] vdac_enable: on:0,module_sel:8
[ 64.637003@0] tv_vout: new mode =1080p50hz set ok
[ 64.637006@0] vout_serve: vinfo mode is: 1080p50hz
[ 64.637010@0] vout_serve: new mode 1080p50hz set ok
[ 64.637025@0] hdmitx: video: auto - get current mode: 1080p50hz
[ 64.637029@0] hdmitx: stream colourdepth was 8 in para 0x01b45050 (invalid)
[ 64.637032@0] hdmitx: display colourdepth was 8 in cur_param 0x01b44310 (VIC: 31)
[ 64.637036@0] hdmitx: update rx hdr info 5
[ 64.637039@0] hdmitx: update physcial size: 1600 900
[ 64.637052@0] hdmitx: hdev->para now = para at 0x01b46330
[ 64.637057@0] hdmitx: display colourdepth is 8 in cur_param 0x01b44310 (VIC: 31)
[ 64.637062@0] hdmitx: Stream colourdepth is 8 in para 0x01b46330 (1920x1080p50hz - VIC: 31)
[ 64.637100@0] hdmitx: system: already init VIC = 0 Now VIC = 31
[ 64.637105@0] hdmitx: system: params found at 0x01b44310
[ 64.637108@0] hdmitx: system: cur_param = param at 0x01b44310 colourdepth 8
[ 64.637116@0] hdmitx: video: pixel freq 148500, tmds clock 148500, MaxClock1 300000, HF_IEEEOUI 0xc45dd8, MaxClock2 600000
[ 64.637121@0] hdmitx: rx has SCDC present indicator
[ 64.639134@0] hdmirx version is 2.0
[ 64.639138@0] hdmitx div40: 0
[ 64.663756@1] hdmitx: system: set pll
[ 64.663761@1] hdmitx: system: param->VIC:31
[ 64.663766@1] hdmitx: set clk: VIC = 31 cd = 4 frac_rate = 0
[ 64.663773@1] hdmitx: 1920x1080p50hz doesn't have frac_rate
[ 64.663782@1] config HPLL = 2970000
[ 64.663805@1] HPLL: 0xc000027b
[ 64.663808@1] config HPLL done
[ 64.663818@1] set_hpll_od3_clk_div[442] div = 6
[ 64.663827@1] j = 4 vid_clk_div = 1
[ 64.663838@1] hdmitx: set enc for VIC: 31
[ 64.663862@1] hdmitx_set_hw[4896] set VIC = 31
[ 64.663920@1] Set rgb_ycc to 2
[ 64.664084@0] hdmitx: system: irq 80000001
[ 64.664108@0] Start = 0x10000100 End = 0x100001ff
[ 64.664121@0] [0x10000104]: 0x00000001
[ 64.664317@0] [0x10000180]: 0x000000ff
[ 64.664323@0] [0x10000181]: 0x000000ff
[ 64.664328@0] [0x10000182]: 0x00000003
[ 64.664334@0] [0x10000183]: 0x00000007
[ 64.664340@0] [0x10000184]: 0x0000003f
[ 64.664346@0] [0x10000185]: 0x00000002
[ 64.664354@0] [0x10000187]: 0x000000ff
[ 64.664360@0] [0x10000188]: 0x00000003
[ 64.795753@1] hdmitx: system: PHY Setting Done
[ 64.799770@1] Sink is HDMI device
[ 64.799782@1] hdmitx: system: packet: can't get vendor data
[ 64.799788@1] hdmitx: video: vinfo: 1080p50hz 50 1
[ 64.799795@1] hdmitx: video: vinfo recalc: 1080p50hz 50 1
[ 64.799802@1] hdmtix: set audio
[ 64.799814@1] hdmitx tx_aud_src = 0
[ 64.799846@1] hdmitx: fs = 2, cd = 4, tmds_clk = 148500
[ 64.799851@1] hdmitx aud_n_para = 6272
[ 64.799873@1] hdmitx set channel status
[ 64.799939@1] hdmitx: audio: Audio Type: PCM
[ 64.799948@1] hdmitx: video: VIC: 31 (31) 1920x1080p50hz
[ 64.799961@1] hdmitx: video: Bit depth: 8-bit, Colour range RGB: limited, YCC: limited, Colourspace: YUV444
[ 64.799969@1] hdmitx: video: Colorimetry: bt709
[ 64.799976@1] hdmitx: video: PLL clock: 0xc000027b, Vid clock div 0x000a339c
[ 64.799983@1] fb: osd current vmode=1080p50hz, cmd: 0x10000
[ 64.816887@6] fb: osd[0] canvas.idx =0x40
[ 64.816889@6] fb: osd[0] canvas.addr=0xb9300000
[ 64.816892@6] fb: osd[0] canvas.width=7680
[ 64.816893@6] fb: osd[0] canvas.height=2160
[ 64.816895@6] fb: osd[0] frame.width=1920
[ 64.816897@6] fb: osd[0] frame.height=1080
[ 64.877054@6] fb: osd[0] canvas.idx =0x40
[ 64.877057@6] fb: osd[0] canvas.addr=0xb9300000
[ 64.877059@6] fb: osd[0] canvas.width=7680
[ 64.877061@6] fb: osd[0] canvas.height=3240
[ 64.877063@6] fb: osd[0] frame.width=1920
[ 64.877064@6] fb: osd[0] frame.height=1080
[ 67.824200@5] audio_dsp: buf=0
[ 67.824220@5] audio_dsp: IEC958_mode_raw=0
[ 67.824278@5] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 67.824283@5] audio_dsp: last mode 0,now 0
[ 67.832609@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 67.832633@5] aml_spdif_dai: share the same clock
[ 67.832647@5] aml_audio_hw: IEC958 PCM32
[ 67.832658@5] hdmitx: audio: aout notify rate 44100
[ 67.832663@5] hdmitx: audio: aout notify size 32
[ 67.832669@5] hdmitx: audio: no update
[ 67.832688@5] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 67.833331@5] aml_spdif_dai: aml_hw_iec958_init,runtime->rate=44100, runtime->channels=2, same source mode(1)
[ 67.833341@5] aml_spdif_dai: share the same clock
[ 67.833352@5] aml_audio_hw: IEC958 PCM32
[ 67.833361@5] hdmitx: audio: aout notify rate 44100
[ 67.833365@5] hdmitx: audio: aout notify size 32
[ 67.833369@5] hdmitx: audio: no update
[ 67.833384@5] aml_snd_m8_card aml_m8_snd.49: i2s/958 same source
[ 67.833600@5] channel count should be 8, we got 2 aborting
################################################################################
… output of lsmod
LibreELEC release: S912.arm-nightly_20190129
################################################################################
Module Size Used by
8021q 19039 0
hci_uart 30134 1
bluetooth 340354 2 hci_uart