Thank you for quick reply.
For “ON” function I must use original remote which works.
Update
Since Amlogic-ng stable 9.2.4 also GXL devices are supported by inject_bl301!
So wake-up features like CEC and IR should work when BL301 got injected.
The usbpower option is not supported by this platform.
Most IR codes for wake-up need to be defined manually by this guide:
Be aware that this feature and support is still experimental on GXL devices!
It can brick your device from booting and you will need to shorten eMMC to recover the device to unbrick it!
1 Like
Hello, I’ve found this today: https://github.com/CoreELEC/CoreELEC/commit/5397dbdab4aae86cbc84b3df18552bf1dd756cb7
Does this mean that there will be no longer support for injecting gxl devices? Or it’s just a temporary measure?
I’m on 9.2.4.1, patched my x96 mini and (still testing), but using so far without issues.
it will come back but in “manual” mode. there will be no option anymore to inject just from CE settings.
Also there will be a extra warning as it can brick the device and stop booting.
1 Like
I think I identified one remaining issue with GXL injection. It’s about the bl31 blob size does not fit into currently used bootloader on the device. I need to look if this can be fixed.
A bootloader created before 9 June 2017 on GXL devices will get bricked for sure!
1 Like
Hi, I have a Ugoos AM6 Plus and successfully inserted Bl301 through the menu option. I’m using it because I wanted to set the on/off power IR command more accurately since the on/off of my AM6 was triggered by several other IR commands in my TV/receiver setup as well.
Almost all is working well and the on/off triggering by other commands is solved. However, the power button can now only shut down the device. It’s not possible to turn the device on with it. With IR this is no problem.
Does this have anything to do with the gpiopower setting in config.ini? I tried a few settings (under which shutdown didn’t work either so this made the problem worse) but with one setting I got strange messages during boot so I shut off the power and disabled the gpiopower setting again.
Any ideas? Thanks.
Yes, you need to insert the correct gpio number for the power button. I will take a look if I can find it in the Android dtb.
@boot2k3 can you tell me the correct gpio by the dtb from Ugoos?
1 Like
Fantastic! Thanks both 
Has there been any progress supporting S912?
I have inserted the blobs on my minim8s box and it has been working great with cec
I got portisch bootloader working too on my s912 box too
Hi All, So I ended up bricking my T95N S905X. Are there any instructions for recovery? I cant seem to find any other than “shorten eMMC”
Thanks heaps!
When you don’t see the vendor logo on power on it’s bricked and you need to shorten eMMC.
When you open the device may you are able to make a UART Log?
These should provide a starting point for your unbricking
You will of course have to resolve a couple of things for your own device … specific firmware and location of pins to be shorted.
1 Like
I am more interested into your box as it’s a “standard” p212 board. What Android image you had flashed on the device? You have a image for me to check it? Or you had something different installed on the box?
Was there a installtointernal performed or you booted from uSD/USB?
Hi
Inject bl301 is not available in CoreELEC GUI setting with 9.2.4.2 on GXL devices
Yes, this is because it’s still at a experimental development stage. Check the how-to how to use it.
Yes, used it, works like a charm 
Hi everyone,
I am quite new to Coreelec and I bought a box just to run it as it was the kind of OS I needed.
However, after applying the bl301 injection through Coreelec hardware settings, my box never rebooted…
Now, it seems that it won’t power on, it does nothing when pressing the reset/recovery button and I don’t see it on my wired network so I can’t use SSH…
I am wondering if my box is bricked and thus, if I need to try the guide from JohnBoyz or if I am missing something?
The box I have is X96 Max+ 4/64.
Any help will be much appreciated.
Cheers.
Edit: if it is bricked, is there a way to just use the USB burning tool to restore the box to its initial state or is the short circuit the only option?
2nd edit: I opened up my box to check how it was inside and the PCB of teh X96 Max+ is different from the one shown in the guide from JohnBoyz.