Please use a terminal client where you can copy/paste the output to the forum.
Can you please make a latest dump of the dtb with last firmware?
Just use this cmd when booted to CE:
dd if=/dev/dtb | gzip > /storage/downloads/dtb.img.gz
On Android you have gigabit speed?
You can test it by iperf.
Yes is going with good speed and as gigabit. I have only 20/20 speed of my internet provider, but going as usually with gigabit device. I dont know, which terminal know export log from cmd dmesg.dtb.img.gz (50.7 KB)
Yesterday i take photo also from remote control chaneels, maybe it help for better bl grabing from this device for turn on/ turn off.
Please try this dtb:
g12b_s922x_x88_king_rev_a.dtb (70.0 KB)
Move your boot media to a PC and rename this file to dtb.img and copy it to COREELEC partition.
I tried on stabil new coreeelec, and also on nightly with your dtb. Both cases was unsuccessful. I tried dhcp, and static ip, but was no internet still.
Did you use a clean install? Make a new boot media from scratch and use my dtb, you should see Kodi wizard on first boot.
If booted and still not working please do dmesg|paste and five me the link you receive.
You need at least connected to WLAN. Please also connect LAN cable.
Also please do post the link you receive for your debug data using this guide:
Now i finally grab full dmesg from android with active dhcp on LAN. File is here (it was adventure):dmesg.log (169.8 KB)
And CE dmesg & log?
And dmesg|paste?
I do not see anything not working in your dmesg. Please post the output of:
dmesg | grep eth0
ifconfig
And please check if Wired is enabled in Kodi -> Settings -> CE Settings -> Network
Sample:
CoreELEC:~ # dmesg | grep eth0
[ 3.634849@3] eth0: device MAC address 00:1e:06:42:45:2b
[ 10.915080@0] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 10.917437@0] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.916263@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.916284@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
CoreELEC:~ # ifconfig
eth0 Link encap:Ethernet HWaddr 00:1E:06:42:45:2B
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1283 errors:0 dropped:7 overruns:0 frame:0
TX packets:553 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:159000 (155.2 KiB) TX bytes:155269 (151.6 KiB)
Interrupt:14
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
But, when not going lan, how i know send info from ifconfig ? I know connect to box only through wlan from pc with ssh terminal, but results would be impacted from wlan. For this situation we need tools for ifconfig direct in tvbox.
In android was ask on network prefix length, when i set default value: 24. This value is not missing in Coreelec ? I see now value for rx packets as 0 in ifconfig. @anon88919003 ?
Did you check if it’s enabled in CE settings?
Yes, it was from boot in socket, was enabled eth0. After connecting on fake ip 169.x.x.x. i disconnected this lan through this setting from fake connections and only after it started wlan for possibility of commanding through ssh from pc.
You are wrong, it´s no fake IP - maybe You have to learn a little bit
It is fake ip, for fail state. But is true, to the really fake ip is, when i set static ip on this tvbox through coreelec, which show this tvbox as connected, but in reality is not going internet/wokgroup/connection on router.
No.
You are wrong and You have no idea about network.
I am not IT and i am only experienced user in this field. I might call ip as post adress 
I dont see big disparities
About | FAQ | Terms of Service | Privacy Policy | Legal Notice
